Hi Guys
My M will pop out of 5th unless it is in a pull or going down hill. 5th gear does look like it is fully engaging. (I have the hole open as I am preparing to install a pulley drive) A longtime tractor owner and mechanic told me over the years of folks shifting from 4th to 5th will bend the forks. He has heated the fork (not much heat) just below where it is welded to the shift linkage and bent it forward slightly and this solves the problem. Does anyone have experience doing this ? I am set on trying it... I think.
Thanks !
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Bending back a shift fork ?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- BJ Moretz
- 10+ Years
- Posts: 249
- Joined: Wed Apr 20, 2011 10:34 am
- Zip Code: 28661
- Tractors Owned: IHCC Chapter 42
1985 Ford 1310
2007 MF 1533
1942 Farmall M
1970 Farmall Cub
1946 Farmall B
1200 Cub Cadet - Circle of Safety: Y
- Location: Patterson NC
Bending back a shift fork ?
BJ Moretz
Member Chapter 42 IHCC
1970 Farmall Cub
1533 MF
1310 Ford
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
Member Chapter 42 IHCC
1970 Farmall Cub
1533 MF
1310 Ford
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
-
- 10+ Years
- Posts: 4948
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: Bending back a shift fork ?
Dad bent the 4-5 shifter fork on the 560 many many many years ago. I was at that awkward age where farm work was the last thing on my mind, so I didn't witness the fix. Maybe I was just in school that day...
AFAIK, all he did was bend it. What I do know is that after he fixed it, I could run the tractor down the road without holding the lever in 5th.
AFAIK, all he did was bend it. What I do know is that after he fixed it, I could run the tractor down the road without holding the lever in 5th.
- BJ Moretz
- 10+ Years
- Posts: 249
- Joined: Wed Apr 20, 2011 10:34 am
- Zip Code: 28661
- Tractors Owned: IHCC Chapter 42
1985 Ford 1310
2007 MF 1533
1942 Farmall M
1970 Farmall Cub
1946 Farmall B
1200 Cub Cadet - Circle of Safety: Y
- Location: Patterson NC
Re: Bending back a shift fork ?
Thanks for the feed back Matt. That helps.
Have a good one,
Have a good one,
BJ Moretz
Member Chapter 42 IHCC
1970 Farmall Cub
1533 MF
1310 Ford
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
Member Chapter 42 IHCC
1970 Farmall Cub
1533 MF
1310 Ford
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
- BJ Moretz
- 10+ Years
- Posts: 249
- Joined: Wed Apr 20, 2011 10:34 am
- Zip Code: 28661
- Tractors Owned: IHCC Chapter 42
1985 Ford 1310
2007 MF 1533
1942 Farmall M
1970 Farmall Cub
1946 Farmall B
1200 Cub Cadet - Circle of Safety: Y
- Location: Patterson NC
Re: Bending back a shift fork ?
Finally got time to try heating the fork and bending it. It worked great ! I have made a 20 mile tractor ride and it never popped out of 5 th. One tip tho. Never crank the tractor with the pulley drive off the tranny. Oil goes everywhere ! I will not forget that anytime soon !
BJ Moretz
Member Chapter 42 IHCC
1970 Farmall Cub
1533 MF
1310 Ford
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
Member Chapter 42 IHCC
1970 Farmall Cub
1533 MF
1310 Ford
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
Return to “Farmall M, Super M, 400, 450, & 560”
Who is online
Users browsing this forum: No registered users and 8 guests