This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
super c govner
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 5+ Years
- Posts: 35
- Joined: Wed Aug 13, 2014 11:52 am
- Zip Code: 29340
super c govner
I have took the radiator off an the govner housing what do I need to look at to see if it needs replaced
-
- 10+ Years
- Posts: 4948
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: super c govner
You didn't need to take the radiator off. The governor can be removed without doing that. It's not easy but also not the most difficult thing either.
Why did you take the governor off? Depending on what's wrong, you may replace one thing or another.
All you can really replace is the thrust washer and the spring, though.
Why did you take the governor off? Depending on what's wrong, you may replace one thing or another.
All you can really replace is the thrust washer and the spring, though.
-
- 5+ Years
- Posts: 35
- Joined: Wed Aug 13, 2014 11:52 am
- Zip Code: 29340
Re: super c govner
I have ordered a new one bc I have a new carb on it an it's not turning enough rpms it bogs down when pto is engaged with 5 ft. Pull bush hog
-
- 10+ Years
- Posts: 4948
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: super c govner
A whole new governor? That had to be expensive.
There isn't much to the governor, and they're rarely worn so badly that they're causing a problem About the only things that wear out are the spring and the thrust washer.
If the spring is no good, it won't rev up.
If the thrust washer is no good, it won't idle down.
There are also other factors that can cause the engine to not want to rev up or respond to the governor, such as carburetor adjustments, ignition timing, faulty/worn ignition parts...
There isn't much to the governor, and they're rarely worn so badly that they're causing a problem About the only things that wear out are the spring and the thrust washer.
If the spring is no good, it won't rev up.
If the thrust washer is no good, it won't idle down.
There are also other factors that can cause the engine to not want to rev up or respond to the governor, such as carburetor adjustments, ignition timing, faulty/worn ignition parts...
-
- 5+ Years
- Posts: 35
- Joined: Wed Aug 13, 2014 11:52 am
- Zip Code: 29340
Re: super c govner
Wee govner was ab 90 bucks I got it in gonna do some painting an see then fire her off does the main pull have some kinda mark on it for timing like the cubs do ?
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: super c govner
Timing is the same as cubs, but the flywheel doesn't have a mark on it. Gotta find TDC on the compression stroke in Cylinder #1 and work from there.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
-
- 5+ Years
- Posts: 35
- Joined: Wed Aug 13, 2014 11:52 am
- Zip Code: 29340
Re: super c govner
Could the timing be off to the point it bogs under load?
-
- 5+ Years
- Posts: 35
- Joined: Wed Aug 13, 2014 11:52 am
- Zip Code: 29340
Re: super c govner
Tdc on number one cylinder would be near radiator
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: super c govner
Cylinders go 1 2 3 4. 1 is closest to the radiator, 4 is next to the gas tank. Finding TDC on compression is easy. Take the spark plug out and hand crank (if you can) the engine with your finger in the spark plug hole. When you feel air rush past your finger it means you are at the compression stroke (both valves closed). use a flashlight and peak in and slowly rotate the crank until you see the cylinder top out.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
-
- 10+ Years
- Posts: 4948
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: super c govner
Yup, there's no mark on the front pulley, but SUPPOSEDLY there is a mark on the flywheel.
We looked for a mark on our Super C's flywheel for an hour.
We looked for a mark on our Super C's flywheel for an hour.
-
- 5+ Years
- Posts: 35
- Joined: Wed Aug 13, 2014 11:52 am
- Zip Code: 29340
Re: super c govner
Well I have got Govner on no bushed hogged ab 2 hrs an my belts started smoking really bad guess I will figure it out this week ends .. side note it won't let me post pics here says they to big. But any who is the fan support to have a grease fitting on it as mine had a screw .
Return to “Farmall C, Super C, 200 & 230”
Who is online
Users browsing this forum: No registered users and 4 guests