SA 1A-60 Leveling and Grader Blade

Farmall Super A, AV, 100, 130, & 140 1939 - 1973

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
User avatar
Dale Finch
5+ Years
5+ Years
501 Club
501 Club
Posts: 2193
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '55 Cub "Bertha"
'55 Cub "Ben"
'55 Cub "Bailey"
'56 Cub "Boris"
'48 Super A "Bubba"
Circle of Safety: Y
Location: NC, Chapel Hill

SA 1A-60 Leveling and Grader Blade

Postby Dale Finch » Mon Nov 14, 2011 4:31 pm

I have finished sandblasting, priming, and painting my grader, and since I am mid-mounting it, I actually have quite a few unused parts. However, I do NOT have the "Sustitute Drawbar" that mounts between the forward final bolt holes. I do have an extra "regular" drawbar...can this be mounted with the bow forward, allowing the Pivot Axle Mounting Bracket to be attached? If not, does anyone have a substitute drawbar they are willing to part with? Or is anyone talented enough to make one?

Also, does anyone have information on the attachment hardware? Or detailed photos of the assembled mid-mounted grader? The manual that Rudi has generously provided, doesn't have specific info; it assumes certain parts are assembled units. Mine are NOT!!! Thanks, as always, for your help!

Cecil
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 3909
Joined: Tue Jan 11, 2005 12:12 pm
Zip Code: 12184
eBay ID: adak8965
Circle of Safety: Y
Location: Oxford, NY

Re: SA 1A-60 Leveling and Grader Blade

Postby Cecil » Mon Nov 14, 2011 6:16 pm

Dale on a Cub all you do is turn the drawbar around. The only time you would need a substitute bar would be if it had a fast hitch. I would venture that the same is true on the A and Super A also.

User avatar
Don McCombs
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 12111
Joined: Mon Feb 03, 2003 6:45 am
Zip Code: 21550
Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
Circle of Safety: Y
Location: MD, Deep Creek Lake

Re: SA 1A-60 Leveling and Grader Blade

Postby Don McCombs » Mon Nov 14, 2011 6:41 pm

Dale, the substitute drawbar is needed to center mount the blade. PM me your email address and I'll email the manual to you.
Don McCombs
MD, Deep Creek Lake

Image
Proud Member of Maryland Chapter 39

User avatar
Dale Finch
5+ Years
5+ Years
501 Club
501 Club
Posts: 2193
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '55 Cub "Bertha"
'55 Cub "Ben"
'55 Cub "Bailey"
'56 Cub "Boris"
'48 Super A "Bubba"
Circle of Safety: Y
Location: NC, Chapel Hill

Re: SA 1A-60 Leveling and Grader Blade

Postby Dale Finch » Wed Nov 23, 2011 2:48 pm

The blade is completely assembled, but I am still looking for a SUBSTITUTE DRAWBAR. Anyone? Someone must have a spare in their goodie pile!!! Barnyard, Billy, Boss, Dale...??!!

User avatar
Don McCombs
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 12111
Joined: Mon Feb 03, 2003 6:45 am
Zip Code: 21550
Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
Circle of Safety: Y
Location: MD, Deep Creek Lake

Re: SA 1A-60 Leveling and Grader Blade

Postby Don McCombs » Wed Nov 23, 2011 3:23 pm

Dale, post an ad on YTMag. It got me quick results on my platform carrier question.
Don McCombs
MD, Deep Creek Lake

Image
Proud Member of Maryland Chapter 39

User avatar
Dale Finch
5+ Years
5+ Years
501 Club
501 Club
Posts: 2193
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '55 Cub "Bertha"
'55 Cub "Ben"
'55 Cub "Bailey"
'56 Cub "Boris"
'48 Super A "Bubba"
Circle of Safety: Y
Location: NC, Chapel Hill

Re: SA 1A-60 Leveling and Grader Blade

Postby Dale Finch » Wed Nov 23, 2011 8:37 pm

Thanks for the suggestion, I'll do that.

mikeintn
10+ Years
10+ Years
Cub Star!!
Cub Star!!
Posts: 393
Joined: Tue Nov 21, 2006 12:39 pm
Location: Blountville, TN.

Re: SA 1A-60 Leveling and Grader Blade

Postby mikeintn » Sun Nov 27, 2011 8:42 pm

Dale are you still looking for a drawbar for SA, I may have one that the mounting bracket has been welded to the drawbar, if that something your interested in let me know and I'll look and maybe get a picture for you. Mike
Mike

User avatar
Dale Finch
5+ Years
5+ Years
501 Club
501 Club
Posts: 2193
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '55 Cub "Bertha"
'55 Cub "Ben"
'55 Cub "Bailey"
'56 Cub "Boris"
'48 Super A "Bubba"
Circle of Safety: Y
Location: NC, Chapel Hill

Re: SA 1A-60 Leveling and Grader Blade

Postby Dale Finch » Mon Nov 28, 2011 8:47 am

Mike, I am looking for a "SUBSTITUTE DRAWBAR" for mounting my blade under the tractor. I already have two regular drawbars, but the holes are not in the right places. The Substitute drawbar is a "simple" flat bar that goes from one front hole on the final across to the other. It has short verticle arms for the attachment and has several holes along the bar for the blade arms. It is similar to this one, but larger for the SA. http://www.tm-tractor.com/gdr/subdrbar1_001.htm I've never actually seen one, but someone must have one out there somewhere!

If this is what you have, I would be very interested. Thanks

danovercash
10+ Years
10+ Years
501 Club
501 Club
Posts: 3361
Joined: Mon Feb 17, 2003 8:48 pm
Zip Code: 28081
Circle of Safety: Y
Location: NC, Kannapolis

Re: SA 1A-60 Leveling and Grader Blade

Postby danovercash » Mon Nov 28, 2011 9:46 am

Dale, don't see why you could not make a substitute drawbar. I made one for my cub, but put "ears" on the bottom that were too long. turned that thing into a pretzel digging an axle deep pit to bury a burnt brush pile. Sorry, don't have a pix handy (not in computer). I used 1 x 2 flat bar to make mine. Later I built a F/H specific one. It uses the back cultivator holes. You could do the same if you have rear cultivator brackets for your tractor. This one is probably bulletproof as it would take out the finals before breaking.

http://photos.cubfest.com/displayimage.php?pos=-8119

http://photos.cubfest.com/displayimage.php?pos=-12472
"I'd rather be a mechanic in the shop"- Henry Ford

252646 & 221525. 195897 (Gone, but not forgotten)

mikeintn
10+ Years
10+ Years
Cub Star!!
Cub Star!!
Posts: 393
Joined: Tue Nov 21, 2006 12:39 pm
Location: Blountville, TN.

Re: SA 1A-60 Leveling and Grader Blade

Postby mikeintn » Mon Nov 28, 2011 3:51 pm

No Dale cannot help on that, I'm thinking the same, if you dont find one looks like it wouldnt be to hard to make, good luck.
Mike

User avatar
Dale Finch
5+ Years
5+ Years
501 Club
501 Club
Posts: 2193
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '55 Cub "Bertha"
'55 Cub "Ben"
'55 Cub "Bailey"
'56 Cub "Boris"
'48 Super A "Bubba"
Circle of Safety: Y
Location: NC, Chapel Hill

Re: SA 1A-60 Leveling and Grader Blade

Postby Dale Finch » Tue Nov 29, 2011 9:24 am

Well, since I do have a spare set of drawbar brackets, I just sketched a plan for using them to mount a fabricated drawbar. A good project...hard to totally mess up a flat bar with 2 bends in it and a few holes! Besides, the shop owner said "NO PROBLEM" and is helping locate the stock! Couldn't get much better...practice and something to use! Thanks and will get photos up when done. MIGHT have to wait til I return from my dive trip.

P.S. Anyone else here a SCUBA diver? Planning several trips over the next 2 years?!!

User avatar
Winfield Dave
5+ Years
5+ Years
501 Club
501 Club
Posts: 2898
Joined: Thu Apr 22, 2010 2:31 pm
Zip Code: 17953
Tractors Owned: ......Almost enough
Circle of Safety: Y
Location: PA, Middleport (Schuylkill County)

Re: SA 1A-60 Leveling and Grader Blade

Postby Winfield Dave » Tue Nov 29, 2011 12:58 pm

Dale...I thought i remember a comment in the Cub forum [may have been George Willer] that said instead of bends, cut 3 pieces and weld them together...Sometimes hard to get bends in the exact location as far as the width is concerned.
Dave
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill

User avatar
Bigdog
Cub Pro
Cub Pro
501 Club
501 Club
Posts: 24066
Joined: Sun Feb 02, 2003 12:50 pm
Zip Code: 43113
Circle of Safety: Y
Location: OH, Circleville

Re: SA 1A-60 Leveling and Grader Blade

Postby Bigdog » Tue Nov 29, 2011 3:43 pm

If you know how much "gain" you get when making a 90 degree bend you can measure accurately and make two bends. Otherwise it is probably best to make it from 3 pieces and weld it. (Put your welding classes to work Dale!)
Dave - you are correct - It was George Willer's recommendation to fabricate it from 3 pieces with welded joints.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.

My wife says I don't listen to her. - - - - - - - - Or something like that!

Image

http://www.cubtug.com

Jim Becker
Team Cub
Team Cub
501 Club
501 Club
Posts: 12161
Joined: Sun Feb 02, 2003 2:59 pm
Zip Code: 55319
Circle of Safety: Y
Location: MN

Re: SA 1A-60 Leveling and Grader Blade

Postby Jim Becker » Tue Nov 29, 2011 4:40 pm

I think fabrication should be straightforward enough. Choose between bending or welding based on your equipment and relative skills. The big question is the dimensions of the original to determine how heavy it needs to be to keep from bending it. I haven't seen one in years, but I can say it is a LOT heavier than the corresponding Cub part.

Looks like the Parts Depot has a couple new ones. You can probably make several for what one of them will likely cost.

User avatar
Dale Finch
5+ Years
5+ Years
501 Club
501 Club
Posts: 2193
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '55 Cub "Bertha"
'55 Cub "Ben"
'55 Cub "Bailey"
'56 Cub "Boris"
'48 Super A "Bubba"
Circle of Safety: Y
Location: NC, Chapel Hill

Re: SA 1A-60 Leveling and Grader Blade

Postby Dale Finch » Tue Nov 29, 2011 10:36 pm

William and I went out in the cold and picked up what I need for the Substitute Drawbar, plus a better plate for my SA jackstand, plus a piece of pipe to make Dave's Hood Holder/Stand (thanks for the idea, Dave...and whoever gave it to you). So over the next few days, I certainly have something to keep me busy!

Winfield Dave wrote:Dale...I thought i remember a comment in the Cub forum [may have been George Willer] that said instead of bends, cut 3 pieces and weld them together...Sometimes hard to get bends in the exact location as far as the width is concerned.

We came to the same conclusion once I saw just how heavy that steel was...no way was I going to bend THAT stuff! And isn't that the point of a heavy drawbar anyway?? So we DID cut 3 pieces and will weld them. MUCH easier to figure out the needed lengths, too.

Let me know if you think this is a good plan to use the brackets, rather than bolting them directly to a single bolt hole each side. I figure spreading the force out would be easier on the finals, but I still have one cut to make on the crossbar and could leave it long enough without the brackets. (I tried to attach a couple photos, but cannot seem to log on to Photohost.)

I am using the same dimensions as the standard drawbar, 3/4" thick and about 2 1/4" wide, so I think it should be plenty strong.

Input is certainly welcome...and I will try again later to attach some photos.


Return to “Farmall A, Super A, AV, 100, 130 & 140”

Who is online

Users browsing this forum: No registered users and 1 guest