This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
FarmallB Carb Question
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 161
- Joined: Wed Oct 20, 2010 5:32 pm
- Zip Code: 50662
FarmallB Carb Question
I am working on a carb off a B, and it was sludged up bad. The main jet is plugged solid. Anone knowwhat size the jet is, or where I can get one? Thank you.
-
- 10+ Years
- Posts: 161
- Joined: Wed Oct 20, 2010 5:32 pm
- Zip Code: 50662
Re: FarmallB Carb Question
Sorry, I did nopt see the B is in with the F Series.
- Urbish
- 10+ Years
- Posts: 2428
- Joined: Sat Sep 07, 2013 3:45 pm
- Zip Code: 48158
- Tractors Owned: ~
1958 International Cub LoBoy
1947 Farmall H
1946 Farmall B
1953 Willys CJ3B
2022 Massey Ferguson GC1723E Subcompact
Cub Loboy L-54 Leveling and Grader Blade - Circle of Safety: Y
- Location: Manchester, MI
Re: FarmallB Carb Question
Should be the same as an A. Have you looked through the Farmall A manuals? I'd measure mine, but I have a Zenith for an Allis WD on my B; which works, but isn't quite right.
Jim
-
- Team Cub
- Posts: 17272
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: FarmallB Carb Question
Assuming you have a Zenith gasoline carburetor, the parts catalog says early (to serial 61610) is #17 and later is #18.
The Model A guys at fordgarage.com say "The original Ford / Zenith carburetor jet number found stamped on the jet is the orifice size as expressed in 0.05 mm increments. For example, a jet marked number '18' has an orifice diameter of (18)*(0.05) = 0.9 mm = 0.035 inch. " I assume that applies here.
The Model A guys at fordgarage.com say "The original Ford / Zenith carburetor jet number found stamped on the jet is the orifice size as expressed in 0.05 mm increments. For example, a jet marked number '18' has an orifice diameter of (18)*(0.05) = 0.9 mm = 0.035 inch. " I assume that applies here.
-
- Posts: 3
- Joined: Mon May 13, 2019 4:48 am
- Zip Code: N0J1J0
Re: FarmallB Carb Question
I purchased a full rebuild kit and it came with a new jet. My carb had been sitting for decades and fired up after a few turns. I see steiners, amazon and A and I amongst others carry full carb kits. Always worth the extra money to do it all. Usually only an extra $10 or so for a full kit as opposed to a kit which is mostly just gasket replacement.
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: No registered users and 11 guests