This post is to help with the disassembly, inspection, repair, and re-assembly of a Cub governor.
In the parts book, group 12, page 18 is the diagram, part numbers, and description. I have tried to use the same verbage as the parts book, in order to avoid confusion. The numbers in ( ) are the identifying numbers in the parts book.
We begin after the governor has been removed from the tractor and is on the work bench. First thing, clean it up as good as possible at this stage. As we progress, further cleaning will be required.
This governor is part # 251451R1. According to the parts book it was used for
Serial #â€™s 501-106700. So, just a warning, if you have a different gov different part numbers may apply.
Be sure the gov is on a table. Hold it about 2 inches above the table .Hold the gov by the gear and give it some light taps on the ears with a light hammer.
The gear half (18) will start to separate for the housing (20). This may be traumatic if it falls on your foot, so be careful and keep it over the table.
We start with the housing (20). At the bottom, note the rockshaft (8), the
gov tension fork (29) held on by 2 machine screws. This one has only one long arm. It is the same as noted in the parts book. What we are looking for here is excessive ware. The forward most part of the prongs should be shiney from the gov bearing (23) rubbing on them. Shiney, but not worn thin.
But there is another, one with 2 long arms. Donâ€™t worry about this, either one will work just fine.
Remove the screws, tension fork (29), and rockshaft (8).
Note the hole from which the rockshaft (8) was removed. There are 2 items that need to be checked. First from the inside is the rockshaft bearing (10) and from the outside the rockshaft oil seal (9)
Use a small round instrument and move the bearing (10). It should move freely.
Plan on replacing the seal (9).
One can also remove the gov body bumper spring (17 & 18) for inspection.
Normally these will be ok, but take a look.
Wash out the gov body (20). Be careful, donâ€™t want to mess up the bearing (10).
We are now ready to inspect the gov (28).
There are very few things that can go wrong with this. First check the weights (26) to be sure they move freely in and out.
Also need to be sure as the weights move in/out that the gov thrust ball bearing group (23-25) move up and down the gov shaft (28) freely.
Check the gov thrust ball bearing (23) to be sure it rotates freely.
Normally they do, should not be a problem, but check it anyhow.
If all this is ok, clean all parts thoroughly and prepare to re-assemble.
Be prepared to purchase:
Governor spring (7)
Governor rockshaft oil seal (9).
Both need replacing due to age and use. No since doing all this and installing old pieces. These two are the most likely to give problems in the future.
Now, as a side tract: Next photo is of the old and new type gov spring throttle lever (11). There is quite a difference between the old and the new.
Since I am used to the new shorter type, tuning this gov (28) is going to be quite a challenge.
Got to order some parts now, so the final assembly will have to wait. Will do another post at that time.
Time saving tips to keep your Cub running smooth
Moderator: Team Cub
1 post • Page 1 of 1
- 10+ Years
- Posts: 2758
- Joined: Wed Apr 23, 2008 10:10 am
- Zip Code: 70401
- Tractors Owned: 3 barns full of Cubs and implements in various stages of disrepair
- Location: LA, Hammond
- Similar Topics
- Last post
by Lurker Carl
Mon Apr 02, 2018 3:50 pm
by John *.?-!.* cub owner
Sun May 10, 2015 9:13 am
Can governor spring rockshaft arm be removed without removing governor?
kjoiner » Sat Feb 25, 2017 1:57 pm » in Farmall Cub
by Jim Becker
Wed Sep 06, 2017 2:24 pm
by Bus Driver
Sun May 08, 2016 7:48 pm
Tue Jul 12, 2016 12:02 pm
Who is online
Users browsing this forum: No registered users and 0 guests