I have a 1953 Farmall Cub, I have used this to mow and plow snow. This past snow storm I was plowing and the touch controls would not raise or lower the plow. I was advised to remove the fill cap for the hydraulic fluid, and move the touch controls back and fourth to free any air that might have entered the system. However, this did not work.
Does anyone have any clues to what my problem is. Marie
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Hydraulic controls aren't working
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 2
- Joined: Thu Feb 20, 2014 4:48 pm
- Zip Code: 20872
-
- Team Cub
- Posts: 11827
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Hydraulic controls aren't working
Did you check the level of the hydraulic fluid? If you find it is low, check the oil dipstick. If it is high there, you have hydraulic fluid leaking into the oil pan and will need to replace the shaft seal on the pump and change the oil. Also, was the temperature much colder than usual when you were plowing?
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
- ricky racer
- 10+ Years
- Posts: 6315
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: Hydraulic controls aren't working
Is the hyd. fluid level correct? If not, check your Cubs engine oil level. If the engine oil level over full, you need to replace the o-ring on the hydraulic pump. Check it out and report back.
Oh yeah, welcome aboard!! This is the best Cub website on the planet.
Rick
Oh yeah, welcome aboard!! This is the best Cub website on the planet.
Rick
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
- Posts: 3369
- Joined: Mon Feb 17, 2003 8:48 pm
- Zip Code: 28081
- Circle of Safety: Y
- Location: NC, Kannapolis
Re: Hydraulic controls aren't working
Check for missing nut, lock and gear on front of hyd. pump. Nut and lock may be in oil pan. Does the hydraulic system or pump make any noise when running or cycling?
"I'd rather be a mechanic in the shop"- Henry Ford
252646 & 221525. 195897 (Gone, but not forgotten)
252646 & 221525. 195897 (Gone, but not forgotten)
- ricky racer
- 10+ Years
- Posts: 6315
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: Hydraulic controls aren't working
Bob McCarty wrote:Did you check the level of the hydraulic fluid? If you find it is low, check the oil dipstick. If it is high there, you have hydraulic fluid leaking into the oil pan and will need to replace the shaft seal on the pump and change the oil. Also, was the temperature much colder than usual when you were plowing?
Bob
Why didn't I think of that?? You're just a little quicker on the trigger than me, Bob.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- Team Cub
- Posts: 11827
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Hydraulic controls aren't working
Ricky, Great mind think alike.
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 2
- Joined: Thu Feb 20, 2014 4:48 pm
- Zip Code: 20872
Re: Hydraulic controls aren't working
Topped fluid off until it was at the level needed last week. Just pulled the dip stick, it is reading approx. 1/4 inch above full? If the seal for the pump was the cause would the fluid level on the stick be much higher?
- ricky racer
- 10+ Years
- Posts: 6315
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: Hydraulic controls aren't working
If it is leaking, the engine oil level will continue to raise. If the fluid level is up and it still doesn't work, there is a chance that, like danovercash mentioned, the nut could have come off the pump shaft and the gear could have fallen off and dropped down into the oil pan. That is something you can check in about 1/2 hour or so. If the gear in in place, you probably need to direct your attention to the Touch Control unit.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
- Posts: 160
- Joined: Wed Aug 07, 2013 10:09 am
- Zip Code: 14103
- Tractors Owned: 1955 farmall cub w/ fast hitch
Implements:
fast hitch moldboard plow
fast hitch disc harrow
front blade
Danco c-3 mower - Circle of Safety: Y
Re: Hydraulic controls aren't working
danovercash wrote:Does the hydraulic system or pump make any noise when running or cycling?
it should make noise, right? what you're saying is if the gear fell off you wouldn't hear anything from it and there's your problem?
-
- 10+ Years
- Posts: 3369
- Joined: Mon Feb 17, 2003 8:48 pm
- Zip Code: 28081
- Circle of Safety: Y
- Location: NC, Kannapolis
Re: Hydraulic controls aren't working
Some tractors "whine" more than others. If it used to make noise and is quiet, that's a flag. Or listen to the pump with a stethoscope or long screw driver with handle next to ear and listen for gears turning.
"I'd rather be a mechanic in the shop"- Henry Ford
252646 & 221525. 195897 (Gone, but not forgotten)
252646 & 221525. 195897 (Gone, but not forgotten)
Who is online
Users browsing this forum: Scrivet and 28 guests