This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Whitch Alternator?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 2917
- Joined: Sat Feb 11, 2006 5:26 pm
- Location: NC
Re: Whitch Alternator?
Regarding the 10SI Delco, it does matter which one chooses. I bought all of mine from the wrecking yard. Now the yards do not get in many vehicles of that vintage since the alternators changed probably 20 years ago. The 10SI from a Chevette will not fit under the hood of a Cub. But it might be useful for some applications. The 15SI has a slightly larger body that might not be noticeable while rummaging through a pile of alternators in semi-darknesss. I think that the 15SI would not work on the Cub.
The 10SI was made for on-road vehicles in ratings from 37 to 63 amperes. Some lower rated 10SI for off-road vehicles may have been made. I do have a 15SI with 70 amp rating on a larger tractor.
For the newbies, the resistor (or diode or indicator lamp) associated with the alternator is to limit the current flow on the exciter terminal that can feed back to the ignition, if the tractor has battery ignition. If the exciter receives it's power from the ignition switch ( the most convenient arrangement), when charging, the exciter supplies enough power to power the ignition. Thus the tractor would keep on running even after the ignition switch is turned off. The devices mentioned above keep the current backfeed to the ignition too small to supply the ignition, but still are adequate for the supply to the exciter.
IH used a resister on their tractors, a 25 ohm wirewound.I often use a 44 ohm 5 watt wirewound as that is the most common value stocked at the local electronics wholesaler. Values up to 53 ohms will work. Have not tested higher resistance.
The 10SI was made for on-road vehicles in ratings from 37 to 63 amperes. Some lower rated 10SI for off-road vehicles may have been made. I do have a 15SI with 70 amp rating on a larger tractor.
For the newbies, the resistor (or diode or indicator lamp) associated with the alternator is to limit the current flow on the exciter terminal that can feed back to the ignition, if the tractor has battery ignition. If the exciter receives it's power from the ignition switch ( the most convenient arrangement), when charging, the exciter supplies enough power to power the ignition. Thus the tractor would keep on running even after the ignition switch is turned off. The devices mentioned above keep the current backfeed to the ignition too small to supply the ignition, but still are adequate for the supply to the exciter.
IH used a resister on their tractors, a 25 ohm wirewound.I often use a 44 ohm 5 watt wirewound as that is the most common value stocked at the local electronics wholesaler. Values up to 53 ohms will work. Have not tested higher resistance.
Luck favors those who are prepared
-
- 10+ Years
- Posts: 4949
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: Whitch Alternator?
Oh yeah, a 1-wire alternator for sure is simpler.
Cheapest I can get one of those locally is $150. It's an aftermarket "speed" part. Didn't come as stock on any cars that I'm aware of.
Standard 3-wire 10SI's are $40 or so, though we haven't been having the greatest of luck with these... We've gone through 3 of the cheapies on Dad's W-400 so far.
Cheapest I can get one of those locally is $150. It's an aftermarket "speed" part. Didn't come as stock on any cars that I'm aware of.
Standard 3-wire 10SI's are $40 or so, though we haven't been having the greatest of luck with these... We've gone through 3 of the cheapies on Dad's W-400 so far.
-
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Re: Whitch Alternator?
Just for general info, if you already have an older alternator SI that does not self excite, you can change the regulator to a self excitable regulator and the alternator will be self exciting one wire....Cost very little ...5 or 10 bucks...And Amps is based on the load the alternator is capable of producing...It don't pump out 60 or 80 amps unless it needs it...Check out your amp meter if you're in doubt... ![Very Happy :D](./images/smilies/icon_biggrin.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
In Memory of 58,286
-
- 10+ Years
- Posts: 321
- Joined: Wed Jan 21, 2009 2:17 pm
- Zip Code: 78736
- Tractors Owned: two 1948 Cubs
1951 Super A
Kubota L2350 - Location: Austin, TX
Re: Whitch Alternator?
...It don't pump out 60 or 80 amps unless it needs it...
When does it need to?
When all components are operating normally? no
When charging a good battery? no
When you don't have a shorted cable? no
When you don't have a shorted battery cell? no
All I'm saying is to fuse your alternator to protect your equipment when something fails. Look at the following discussions, these things happen and we don't get to choose when, that's when we need a fuse.
http://www.mastercraft.com/teamtalk/arc ... -8243.html
http://www.yotatech.com/f116/my-alterna ... off-97932/
http://www.supraforums.com/forum/showth ... nyone-Help
http://www.lxforums.com/board/f77/alter ... lp-198247/
http://forum.mazda6club.com/electrical/ ... rning.html
http://www.benzworld.org/forums/w140-s- ... urned.html
and on and on.
-
- 10+ Years
- Posts: 127
- Joined: Tue Sep 17, 2013 7:22 pm
- Zip Code: 01073
Re: Whitch Alternator?
Well, I thought I was getting un-confused, but the later postings here are re-confusing me.
Is the Napa # is 2134011SW alternator 1-wire or 3-wire? Does it fit under the Cub hood or not?
Is the Napa # is 2134011SW alternator 1-wire or 3-wire? Does it fit under the Cub hood or not?
Jay Smith
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
-
- 10+ Years
- Posts: 3414
- Joined: Wed May 11, 2011 8:59 pm
- Zip Code: 39154
- Tractors Owned: 1969 Farmall Cub
1952 Cub
1942 Farmall H - Location: Raymond, MS
Re: Whitch Alternator?
RustyKnuckles wrote:Well, I thought I was getting un-confused, but the later postings here are re-confusing me.
Is the Napa # is 2134011SW alternator 1-wire or 3-wire? Does it fit under the Cub hood or not?
Glad to see I'm not the only one!
![Smile :-)](./images/smilies/icon_smile.gif)
Thomas
-
- 10+ Years
- Posts: 1607
- Joined: Sat Jun 03, 2006 8:09 am
- Zip Code: 45387
- Location: Yellow Springs, Ohio
Re: Whitch Alternator?
Well, guess I'm going to muddy the waters as I have used Nippondenso units on the few tractors I've converted for my own, as well other folks who bring their tractors to me to either restore or repair.
Granted they aren't a single wire alternator, but they are still simple to wire. I prefer them as I can get them at salvage yards for normally $20-$30 as they are used on a lot of vehicles (both foreign and domestic brands), the salvage folks always test them before I purchase them to ensure they work and do offer a bit of a warranty (90 days normally) and they are small and compact and the fan is internal within the housing, and I sort of think the other alternators with the clunky fan directly behind the pulley looks ugly.
Granted they aren't a single wire alternator, but they are still simple to wire. I prefer them as I can get them at salvage yards for normally $20-$30 as they are used on a lot of vehicles (both foreign and domestic brands), the salvage folks always test them before I purchase them to ensure they work and do offer a bit of a warranty (90 days normally) and they are small and compact and the fan is internal within the housing, and I sort of think the other alternators with the clunky fan directly behind the pulley looks ugly.
Mike Duncan
-
- Team Cub Guide
- Posts: 3280
- Joined: Thu Feb 20, 2003 4:54 pm
- Zip Code: 71203
- Tractors Owned: 1948,55, and 56 Farmall Cubs.
- Circle of Safety: Y
- Location: Louisiana
Re: Whitch Alternator?
Sometimes you just get that feeling about a particular thread.
As I said on page one..."Always use what you're most comfortable with. I'm sure the hitachi is good and affordable. "
As to my last 12v conversion, I used the same Delco 10SI that most everyone else uses for their conversions. I used simple easy to make brackets, however I may could have made the generator brackets work???? I used Bob Melville's 3 wire diagram and I incorporated a voltmeter. (By the way....an automotive style meter usually comes with a bulb for night lighting......it works good for the diode.) I didn't have to alter the hood for it to fit.
![Image](http://p0.craigupload.com/h/cb6b/0/143467.jpg)
Of all that has seen my '56.....i've not had any comments on the awkward alternator cooling fan or smaller width pulley.
But it bears repeating.....go with what you know and what you're confident in.![Wake Up :coffee:](./images/smilies/emoticon-0162-coffee.gif)
![Confused :?](./images/smilies/icon_confused.gif)
As I said on page one..."Always use what you're most comfortable with. I'm sure the hitachi is good and affordable. "
As to my last 12v conversion, I used the same Delco 10SI that most everyone else uses for their conversions. I used simple easy to make brackets, however I may could have made the generator brackets work???? I used Bob Melville's 3 wire diagram and I incorporated a voltmeter. (By the way....an automotive style meter usually comes with a bulb for night lighting......it works good for the diode.) I didn't have to alter the hood for it to fit.
![Image](http://p0.craigupload.com/h/cb6b/0/143467.jpg)
Of all that has seen my '56.....i've not had any comments on the awkward alternator cooling fan or smaller width pulley.
But it bears repeating.....go with what you know and what you're confident in.
![Wake Up :coffee:](./images/smilies/emoticon-0162-coffee.gif)
-
- 10+ Years
- Posts: 127
- Joined: Tue Sep 17, 2013 7:22 pm
- Zip Code: 01073
Re: Whitch Alternator?
"go with what you know and what you're confident in"
Since I don't know anything about these alternators, and have (therefore) little confidence in doing this successfully, I am just hoping to find an utterly unambiguous, "12 Volt Conversion for Dummies" recipe, with all parts listed (with sources!) and all assumptions and "gotchas" discussed.
Since I don't know anything about these alternators, and have (therefore) little confidence in doing this successfully, I am just hoping to find an utterly unambiguous, "12 Volt Conversion for Dummies" recipe, with all parts listed (with sources!) and all assumptions and "gotchas" discussed.
Jay Smith
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
-
- Cub Pro
- Posts: 1871
- Joined: Sun Mar 30, 2003 10:25 am
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: Restored: 1950 Cub, 1950 Cub Demo, 1948 super AI, 1935 Silver King, 1946 Oliver 60 RC, John Deere M, 1950 C demo.
In working clothes:
1950 cub, 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial. IH 450, 1963, another 1948 cub, 1946 I6 with Trogan front blade. - Location: CT, Middletown
Re: Whitch Alternator?
I guess i'll toss in my 2 cents. mostly, I use the hitatchi 14231. it's a little smaller than the 10SI and gives me a little more adjustment room, as well as using the existing bracket. wiring is simple, a 1n1004 diode on the L term back to the ign switch. connect the other two. I leave the regulator in place with the wire going nowhere... can't hardly tell it's been changed.
on larger equipment, diesels and such, I use the napa 10SI for more power and easier mounting. sometimes you have to play with pulleys to get things to fit properly.
on a cub, you cannot get 63 amps out of it anyway, it won't turn fast enough. so, no worrys there.
Hitatchi 14231 on Amazon $44 free shipping. works for me.
I like pertronics 12 as well....but that's another discussion.... and voltmeters
on larger equipment, diesels and such, I use the napa 10SI for more power and easier mounting. sometimes you have to play with pulleys to get things to fit properly.
on a cub, you cannot get 63 amps out of it anyway, it won't turn fast enough. so, no worrys there.
Hitatchi 14231 on Amazon $44 free shipping. works for me.
I like pertronics 12 as well....but that's another discussion.... and voltmeters
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
-
- 10+ Years
- Posts: 2253
- Joined: Fri Sep 10, 2010 5:23 pm
- Zip Code: 39861
- Tractors Owned: 76 Cub Denim Springs
49 Cub Denim Springs
51 Cub Uncle Harvey
"Jacksonville" 53 Cub
"Jackson" 76 Cub
"Louie" 64 Cub Fast Hitch
"Paw Paw"71 Cub Fast
Hitch
"Alvin" 72 Cub
"Ugly" 75 Cub
76 Cub Val
Mr. Kirkland" 77 Red Cub
77 Cub "Russell
76 Cub w/fast hitch "Edgar"
76 - 185 Cub Lo Boy
John Deere 2003 - 5320
Kubota 7060
Kubota 5400
Kubota 2680
John Deere 445
TO20 Ferguson - Circle of Safety: Y
- Location: Jakin Georgia
Re: Whitch Alternator?
Yes the NAPA alternator is one wire and yes with the right size belt it fits perfectly under the hood.
"I ain't believing this!"
-
- 10+ Years
- Posts: 127
- Joined: Tue Sep 17, 2013 7:22 pm
- Zip Code: 01073
Re: Whitch Alternator?
artc-
"1n1004 diode on the L term back to the ign switch. connect the other two"
Diode pointed which way? Towards the alternator?
"connect the other two" [wires] To each other? And not to anything else?
And you don't need any other bracketry besides the original for the generator?
Any info appreciated!
"1n1004 diode on the L term back to the ign switch. connect the other two"
Diode pointed which way? Towards the alternator?
"connect the other two" [wires] To each other? And not to anything else?
And you don't need any other bracketry besides the original for the generator?
Any info appreciated!
Jay Smith
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
-
- 10+ Years
- Posts: 127
- Joined: Tue Sep 17, 2013 7:22 pm
- Zip Code: 01073
Re: Whitch Alternator?
Tezell -
" with the right size belt it fits perfectly under the hood"
What size belt is the right size belt?
Thx!
" with the right size belt it fits perfectly under the hood"
What size belt is the right size belt?
Thx!
Jay Smith
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
1953 Cub, acquired fall 2013. Runs much better thanks to tuneup by Art Chester!
Next, replacement of old parts (radiator, seals, etc.) + painting.
Plus 3 JD garden tractors (425,318,140)
& two Buick Roadmaster station wagons
-
- Cub Pro
- Posts: 10290
- Joined: Mon Oct 24, 2005 8:35 pm
- Zip Code: 23962
- eBay ID: dmb2613
- Circle of Safety: Y
- Location: VA. Randolph
Re: Whitch Alternator?
RustyKnuckles wrote:Tezell -
" with the right size belt it fits perfectly under the hood"
What size belt is the right size belt?
Thx!
It will depend on the pulley on the fan, the early models had a small pulley the later models had a large pulley, the late models take a 22 inch belt I think, and the early ones a 21 inch belt. I think I may have explained this on one of my how to post. Most likely you can use the belt you have now.
IN GOD WE TRUST
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
-
- 10+ Years
- Posts: 321
- Joined: Wed Jan 21, 2009 2:17 pm
- Zip Code: 78736
- Tractors Owned: two 1948 Cubs
1951 Super A
Kubota L2350 - Location: Austin, TX
Re: Whitch Alternator?
on a cub, you cannot get 63 amps out of it anyway, it won't turn fast enough. so, no worrys there.
Correct, on a Cub you can't get full rated current output.
But, crank pulley diameter 5"
Alternator pulley diameter 2.6"
Alternator shaft speed at 1600 RPM (speed that drawbar power test was done) is 1600x(5/2.6)=3076 RPM
At this speed, the 10si can deliver 44 amps from the Delco specs
But enough to worry about without a fuse in the charging wire.
Whichever alternator you use, wire in a fuse. All the diagrams I've seen don't use a fuse except the one I posted.
I've never seen a discussion topic so polarized (pun intended)
I guess it's time to quit beatin' a dead horse.
Gerry
Last edited by Gerry Powell on Tue Oct 22, 2013 5:48 pm, edited 1 time in total.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 6
- 276
-
by ajhbike
Mon Jul 26, 2021 6:42 pm
-
- 11
- 439
-
by Dusty B
Fri Nov 11, 2022 6:12 pm
-
- 9
- 271
-
by phill_mi
Fri Dec 16, 2022 7:30 pm
-
- 28
- 713
-
by phill_mi
Wed Jun 28, 2023 8:53 pm
-
- 8
- 433
-
by tmays
Sat Mar 04, 2023 6:27 pm
Who is online
Users browsing this forum: No registered users and 5 guests