I decided to restore my sickle mower this weekend. I had read numerous posts on here about just hitting the rivets with a hammer and off pop the blades. Woosh. What kind of hammers was everyone else using? the bar and blades were pretty rusty so that may have had an effect but all I did with the hammer was flatten the heads of the rivets more and bend the bar a bit. So I went to the grinder and ground off one side and then with the punch. I still have about 6 to punch out. This was after generous helpings of PB blaster and several hours of work with sufficient breaks in between to say a confession or two for all the cursing. I even picked up an anvil off craigslist last night to make the job easier and to plan ahead for the rivets to come.
I am checking with Columbia tractor to see if they sell the perforated metal bar that holds the blades. If so, next time I will just chuck the old bar and old blades and start anew.
In spite of it all, it was a fun learning experience. I learned there has to be a better way for sickle mower number 2!
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
hammering the sickle mower
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 240
- Joined: Mon Apr 09, 2007 5:00 pm
- Location: fairfield ct
hammering the sickle mower
1947 cub #7131
1948 cub
1949 cub #91491
1949 cub #93744
1950 cub #110652
1960 cub
1928 Overland Whippet
1929 Ford Model A roadster
1948 cub
1949 cub #91491
1949 cub #93744
1950 cub #110652
1960 cub
1928 Overland Whippet
1929 Ford Model A roadster
- Don McCombs
- Team Cub Mentor
- Posts: 17480
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
Re: hammering the sickle mower
Removing the sections does involve a hammer, but not in the manner you used. Perhaps a through read of this manual will make the task easier.
http://www.cleancomputes.com/Cub/Cub%20 ... index.html
http://www.cleancomputes.com/Cub/Cub%20 ... index.html
- Bill Hudson
- Team Cub
- Posts: 9522
- Joined: Wed Jul 26, 2006 10:50 am
- Zip Code: 44057
- Tractors Owned: 57 F-Cub - Dad & Mom's Cub
77 F-Cub - Red Long Stripe - Circle of Safety: Y
- Location: OH, Madison
Re: hammering the sickle mower
Bill,
I'll do my best to explain how to snap the sections off with a hammer. First, do not hit the rivets. You found out what happens when you do.
Now to remove the sections with a hammer you will use your anvil, a (preferably) big ball pein hammer, and the section bar. Orient the sections with the tip pointing down them place the bar on the top of the anvil with the sections on the side of the anvil. The only thing above the working surface of the anvil will be the rectangular bar and the back edge or the sections. Take the hammer and smack(hard) the the back edge of the section. The section should snap off easily with one, or possibly two hits. If it takes more, swing with more force or get a bigger hammer. The rivets that remain in the bar can be driven out with a punch; the hardy hole will work well for this.
I have removed more sections than I care to remember using this method. I was Dad's "Johnson Sickle Servicer." Oh, what I had to use was much more crude than your anvil.
Bill
Boy, Don is fast.
I'll do my best to explain how to snap the sections off with a hammer. First, do not hit the rivets. You found out what happens when you do.
Now to remove the sections with a hammer you will use your anvil, a (preferably) big ball pein hammer, and the section bar. Orient the sections with the tip pointing down them place the bar on the top of the anvil with the sections on the side of the anvil. The only thing above the working surface of the anvil will be the rectangular bar and the back edge or the sections. Take the hammer and smack(hard) the the back edge of the section. The section should snap off easily with one, or possibly two hits. If it takes more, swing with more force or get a bigger hammer. The rivets that remain in the bar can be driven out with a punch; the hardy hole will work well for this.
I have removed more sections than I care to remember using this method. I was Dad's "Johnson Sickle Servicer." Oh, what I had to use was much more crude than your anvil.
Bill
Boy, Don is fast.
-
- Team Cub
- Posts: 11854
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: hammering the sickle mower
Illustration 11 on page 11 is the way to do it. Next time check and see if someone nearby has a Johnson Sickle Servicer. Makes the job much easier.
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
- Barnyard
- Team Cub
- Posts: 24268
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
- Contact:
Re: hammering the sickle mower
If you plan to do many of these you may want to get a Johnson sickle serving tool. it makes the job a whole lot easier.
One thing not shown are the end two or three knives that have to be done with a hammer and punch.
One thing not shown are the end two or three knives that have to be done with a hammer and punch.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 10+ Years
- Posts: 240
- Joined: Mon Apr 09, 2007 5:00 pm
- Location: fairfield ct
Re: hammering the sickle mower
thanks everyone. Boy do I feel dumb.
1947 cub #7131
1948 cub
1949 cub #91491
1949 cub #93744
1950 cub #110652
1960 cub
1928 Overland Whippet
1929 Ford Model A roadster
1948 cub
1949 cub #91491
1949 cub #93744
1950 cub #110652
1960 cub
1928 Overland Whippet
1929 Ford Model A roadster
-
- 10+ Years
- Posts: 4948
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: hammering the sickle mower
I've done two bars, and what I do is open up my bench vice just enough that the sections slip down between the jaws easily. Hang the bar on one jaw of the vise, and knock the back edge of the sections with whatever hammer happens to be within reach, usually a 2lb one-handed sledge.
- Barnyard
- Team Cub
- Posts: 24268
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
- Contact:
Re: hammering the sickle mower
When doing it according to the manual as Don, Bob and Matt mention, you can still end up with a bit of warping, but that is easily straightened.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
- twotone
- 10+ Years
- Posts: 1189
- Joined: Sat May 14, 2011 6:09 pm
- Zip Code: 15132
- Tractors Owned: 53 F Cub
73 F Cub
53 Super A With Snow/Grader Blade
193 Plow With Colter And Jointer
144 Cultivators
22 Mower - Circle of Safety: Y
- Location: Versailles,Pa.
Re: hammering the sickle mower
I did mine the hard way. I ground off the heads and then used a rivet tool that will either punch the rivet out, or will smash it down when installing new rivets. I found it much easier and cheaper to buy a whole knife section at a farm supply store. The one I bought was 7 feet long, just cut to length and you're done.
Know Your Cub, And Your Cub Will Know You.
Tom
Tom
-
- 10+ Years
- Posts: 398
- Joined: Tue Nov 30, 2010 7:54 pm
- Zip Code: 23027
- Circle of Safety: Y
Re: hammering the sickle mower
What's the best method for installing the new sections if you don't have any special tools? Also has anyone tried the pan top bolts with the cub sickle mower for installing the cutting blades?
-
- 10+ Years
- Posts: 240
- Joined: Mon Apr 09, 2007 5:00 pm
- Location: fairfield ct
Re: hammering the sickle mower
I was planning on banging the rivets in with a large hammer and the anvil. I did such a good job flattening the heads on the rivets when I tried to remove the blades that I consider myself pretty good at it now. but I am open to suggestions.
1947 cub #7131
1948 cub
1949 cub #91491
1949 cub #93744
1950 cub #110652
1960 cub
1928 Overland Whippet
1929 Ford Model A roadster
1948 cub
1949 cub #91491
1949 cub #93744
1950 cub #110652
1960 cub
1928 Overland Whippet
1929 Ford Model A roadster
- twotone
- 10+ Years
- Posts: 1189
- Joined: Sat May 14, 2011 6:09 pm
- Zip Code: 15132
- Tractors Owned: 53 F Cub
73 F Cub
53 Super A With Snow/Grader Blade
193 Plow With Colter And Jointer
144 Cultivators
22 Mower - Circle of Safety: Y
- Location: Versailles,Pa.
Re: hammering the sickle mower
I re-did a 4 1/2 foot mower with the pan head bolts. I haven't tried it yet, but they do clear the guards, so it should work fine.
Know Your Cub, And Your Cub Will Know You.
Tom
Tom
-
- 10+ Years
- Posts: 341
- Joined: Wed Nov 08, 2006 9:35 pm
- Location: Backswamp North Carolina
- Contact:
Re: hammering the sickle mower
I have mine done with the pan head bolt kit from International Harvester. It has held for three seasons I am overdue knives. Two of the knives have worked loose this season but after 3 years I can't conplain. My knives are really dull at this point. I am going to try rivets this time.
1961 Cub
1948 Cub
1960 CUB
1964 CUB CADET 100
23A Disc,2-C-22 sickles,54 Blade,152 disc,38a lift disc,C2 Mower,Kub Klipper, and a side dresser.
1948 Cub
1960 CUB
1964 CUB CADET 100
23A Disc,2-C-22 sickles,54 Blade,152 disc,38a lift disc,C2 Mower,Kub Klipper, and a side dresser.
Who is online
Users browsing this forum: No registered users and 7 guests