This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link:
Privacy Policy

NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.

parts estimate

The Cub Club -- Questions and answers to all of your Cub related issues.
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
southernthunder
10+ Years
10+ Years
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Mon Mar 11, 2013 11:02 pm

Update: after a lot of searching the web and such for crossover numbers I finally got almost everything ordered for my tranny/ final drive rebuild. the only bearing I have not got as a Timken replacement was the front spline shaft (it was another brand) and the rear spline shaft bearing. I have skf,new departure,agco,ntn and several more cross numbers that will work if I slightly reduce the diameter of the shaft that goes in it. I found this info in an old post here because several people were having trouble due to wear on the shaft from the original rollers direct on shaft. Sounds like a good cheaper fix to tighten this up. Total is looking like about $500 which includes doubling each seal where there is room. Any suggestions on anything else I may need to replace while in it. I have all the seals, gaskets and bearings I can find in the parts book. just hoping to have everything in the shop when I start the rebuild. thanks guys

SPONSOR AD

Sponsor



Sponsor
 

User avatar
bob in CT
Team Cub Mentor
Team Cub Mentor
Posts: 6018
Joined: Thu Jun 07, 2007 9:34 am
Zip Code: 06040
Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
Circle of Safety: Y
Location: CT, Manchester

Re: parts estimate

Postby bob in CT » Tue Mar 12, 2013 4:46 am

Someone on this board commented that using 2 seals was not a good idea. The seals are designed to run wet. The outside seal will wear quickly and just become a dirt trap that will degrade the inner seal. Better to use the thinner seal to choose a clean, unworn spot on the shaft to do its job.

southernthunder
10+ Years
10+ Years
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Tue Mar 12, 2013 5:42 am

thanks for the imput bob. all of the research I found on here suggested to use 2 seals in the place of some of the original double seal (rubber and leather). Maybe I should start another thread and ask everyone what they think. If that's the case I will have a start on parts for my next project :D thanks

User avatar
bob in CT
Team Cub Mentor
Team Cub Mentor
Posts: 6018
Joined: Thu Jun 07, 2007 9:34 am
Zip Code: 06040
Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
Circle of Safety: Y
Location: CT, Manchester

Re: parts estimate

Postby bob in CT » Tue Mar 12, 2013 6:56 am

If memory serves me, it was Steve K. Calif that posted this. He is a bearing and seal professional.

southernthunder
10+ Years
10+ Years
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Tue Mar 12, 2013 7:04 am

with all of the input I received so quickly on the new post, and from your suggestion, I will only be putting a single seal in the most appropriate, smoothest spot on the shaft for each location.. thanks so much, mike

User avatar
bob in CT
Team Cub Mentor
Team Cub Mentor
Posts: 6018
Joined: Thu Jun 07, 2007 9:34 am
Zip Code: 06040
Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
Circle of Safety: Y
Location: CT, Manchester

Re: parts estimate

Postby bob in CT » Tue Mar 12, 2013 7:24 am

You will like the sealed bearing fix for the input shaft. I did that for my 1950 Cub project and I was very pleased with the results.

southernthunder
10+ Years
10+ Years
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Tue Mar 12, 2013 7:57 am

that's my plan for it and the pto bearing. if the replacements come sealed, I am just going to leave them that way. It should last me or my girls or whoever they sell it to when I am gone.


Return to “Farmall Cub”

Who is online

Users browsing this forum: No registered users and 34 guests