This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Angle Snowplow Blade Manually NEW VIDEO ADDED
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 3562
- Joined: Thu Apr 22, 2010 2:31 pm
- Zip Code: 17953
- Tractors Owned: ......Almost enough.
N3NIK - Circle of Safety: Y
- Location: PA, Middleport (Schuylkill County)
Angle Snowplow Blade Manually NEW VIDEO ADDED
This came about because I started plowing snow with my newest Cub, Hercules.
And realized very quickly that getting off and on to change the angle of the blade was for the birds.
I didn't want to spend the money or the time to install the hydraulic angling system some have on their plows,
so I started thinking about alternatives.
Being able to pull a cable to raise the pin, swivel the blade and drop the pin, all from from the driver's seat.
Here is one way to make snow plowing more enjoyable at a very low cost.
The hardest part of this project was the spring loaded pin (latch).
I tried to buy a pre-made one like this http://www.harborfreight.com/spring-gate-latch-assembly-95018.html
but the pin is only 1/2", not 5/8" like the typical blade pin.
You may want to go this route - it is a sloppy fit - but it makes the hole alignment easier.
So, I ended up making a latch. [There may be a latch available to purchase, I didn't want to spend the time looking]
Since there wasn't any tube or channel around our place, I formed a bracket from 1/4" steel.
Found a spring, cut a piece of 5/8" diameter rod and added a roll pin.
I figured on having 1-1/4" of rod protrude below the bracket into the blade holes.
Then welded a piece of a chain link that was lying on the table for a loop.
Tack welded it in place...This is a very tricky part....Hole alignment is critical.
I actually cut mine off and re-tacked it in a slightly different location.
It would be a good idea to check the bushing in your pivot bolt...this helps with hole clearances.
Also, the holes can be slightly off depending on whether the blade is suspended or lying on the ground.
After I was final welded, I ran a 5/8" drill bit thru the bracket into all of my holes.
Latch complete.
You may want to use one of these if you don't want to fab your own pin http://www.harborfreight.com/easy-grip-hitch-pin-91306.html
Rick P. or one of the other talented gents here may refine this idea and fabricate and sell a ready-made bolt-it-on latch with mounting slots for easier adjustment in lining up with your holes....hint, hint.
Then I went looking for some parts for the pulley.
My pulley wouldn't slide over a 1/2" bolt...But there was a bolt on the workbench that had threads messed up at the end.
So I ground it down to slide thru the pulley.
Here it is all assembled.
I had briefly tested the latch [spring-loaded pin assembly] with nylon rope and it seemed to work fine.
But the next day I wasn't happy with the amount of stretch in the rope, so off to the barn to scrounge.
I found a coated metal cable from an old dog run we had. This worked out better.
Still needed to come up with a handle to pull on the cable. And how to anchor it.
Thought about making some sort of lever mounted to the steering post, but there was about a 4" difference in the length of the cable
between the blade in the raised position and the fully lowered position.
I replaced the bolt thru the steering post with an eyebolt. Can you guess what it was from?
Found an old mop handle attached it to the end of the cable.
Routed the rest of the cable.
It works really well.
Below are some videos of the final testing...Pushing against a tree stump [no snowbanks available] to swivel the blade.
It also will swivel by dragging on the ground and turning the wheels one way or the other.
I hope you benefit from this little project. It was fun and it helps keep me in the seat - for more seat time !!
And realized very quickly that getting off and on to change the angle of the blade was for the birds.
I didn't want to spend the money or the time to install the hydraulic angling system some have on their plows,
so I started thinking about alternatives.
Being able to pull a cable to raise the pin, swivel the blade and drop the pin, all from from the driver's seat.
Here is one way to make snow plowing more enjoyable at a very low cost.
The hardest part of this project was the spring loaded pin (latch).
I tried to buy a pre-made one like this http://www.harborfreight.com/spring-gate-latch-assembly-95018.html
but the pin is only 1/2", not 5/8" like the typical blade pin.
You may want to go this route - it is a sloppy fit - but it makes the hole alignment easier.
So, I ended up making a latch. [There may be a latch available to purchase, I didn't want to spend the time looking]
Since there wasn't any tube or channel around our place, I formed a bracket from 1/4" steel.
Found a spring, cut a piece of 5/8" diameter rod and added a roll pin.
I figured on having 1-1/4" of rod protrude below the bracket into the blade holes.
Then welded a piece of a chain link that was lying on the table for a loop.
Tack welded it in place...This is a very tricky part....Hole alignment is critical.
I actually cut mine off and re-tacked it in a slightly different location.
It would be a good idea to check the bushing in your pivot bolt...this helps with hole clearances.
Also, the holes can be slightly off depending on whether the blade is suspended or lying on the ground.
After I was final welded, I ran a 5/8" drill bit thru the bracket into all of my holes.
Latch complete.
You may want to use one of these if you don't want to fab your own pin http://www.harborfreight.com/easy-grip-hitch-pin-91306.html
Rick P. or one of the other talented gents here may refine this idea and fabricate and sell a ready-made bolt-it-on latch with mounting slots for easier adjustment in lining up with your holes....hint, hint.
Then I went looking for some parts for the pulley.
My pulley wouldn't slide over a 1/2" bolt...But there was a bolt on the workbench that had threads messed up at the end.
So I ground it down to slide thru the pulley.
Here it is all assembled.
I had briefly tested the latch [spring-loaded pin assembly] with nylon rope and it seemed to work fine.
But the next day I wasn't happy with the amount of stretch in the rope, so off to the barn to scrounge.
I found a coated metal cable from an old dog run we had. This worked out better.
Still needed to come up with a handle to pull on the cable. And how to anchor it.
Thought about making some sort of lever mounted to the steering post, but there was about a 4" difference in the length of the cable
between the blade in the raised position and the fully lowered position.
I replaced the bolt thru the steering post with an eyebolt. Can you guess what it was from?
Found an old mop handle attached it to the end of the cable.
Routed the rest of the cable.
It works really well.
Below are some videos of the final testing...Pushing against a tree stump [no snowbanks available] to swivel the blade.
It also will swivel by dragging on the ground and turning the wheels one way or the other.
I hope you benefit from this little project. It was fun and it helps keep me in the seat - for more seat time !!
Last edited by Winfield Dave on Fri Jan 21, 2011 12:49 pm, edited 1 time in total.
Dave
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
-
- Team Cub
- Posts: 9535
- Joined: Wed Jul 26, 2006 10:50 am
- Zip Code: 44057
- Tractors Owned: 57 F-Cub - Dad & Mom's Cub
77 F-Cub - Red Long Stripe - Circle of Safety: Y
- Location: OH, Madison
Re: Angle Snowplow Blade Manually
Dave,
Very well done. I'm continually amazed at the level of creativity, both individually and collectively, that resides on this forum.
Bill
Very well done. I'm continually amazed at the level of creativity, both individually and collectively, that resides on this forum.
Bill
-
- 10+ Years
- Posts: 821
- Joined: Wed Aug 18, 2010 3:21 pm
- Zip Code: 18036
- Tractors Owned: Presently
1949 Cub
1953 Cub
Kubota Zero turn - Circle of Safety: Y
- Location: Coopersburg, PA
Re: Angle Snowplow Blade Manually
Neat setup, Some people will do anything to get more seat time.
Now, all you need is some SNOW,SNOW, and more snow.
Great job Dave.
Bruce T.
Now, all you need is some SNOW,SNOW, and more snow.
Great job Dave.
Bruce T.
-
- Team Cub Guide
- Posts: 5636
- Joined: Mon Nov 01, 2004 7:24 am
- Zip Code: 43528
- Tractors Owned: 47(circle cub),48(Floyd backhoe),49,,51,54 and another 55
- Circle of Safety: Y
- Location: OH, Holland
Re: Angle Snowplow Blade Manually
Simple and slick. Well done Dave
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
-
- Team Cub
- Posts: 24282
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
Re: Angle Snowplow Blade Manually
I reckon I will need to do this to mine now too. Thanks Dave.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- Team Cub Mentor
- Posts: 4129
- Joined: Tue Jan 11, 2005 12:12 pm
- Zip Code: 13830
- eBay ID: adak8965
- Circle of Safety: Y
- Location: Oxford, NY
Re: Angle Snowplow Blade Manually
Great job. As mentioned I think you could hook it to the depth lever also.
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Angle Snowplow Blade Manually
Dave:
I wasn't exactly sure how this was going to turn out. I figured it was going to be neat.. but this goes beyond neat.. it is kinda cool Very nice job an thanks for documenting it. I copied it to the How To Forum -- as another one of the How I Did That kind of posts....., locked it and it is now in safely in the In The Barn section of the CBoK Index with the other Cub-54 modifications.
Well done, it is really slick.
I wasn't exactly sure how this was going to turn out. I figured it was going to be neat.. but this goes beyond neat.. it is kinda cool Very nice job an thanks for documenting it. I copied it to the How To Forum -- as another one of the How I Did That kind of posts....., locked it and it is now in safely in the In The Barn section of the CBoK Index with the other Cub-54 modifications.
Well done, it is really slick.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 3034
- Joined: Wed May 31, 2006 12:09 pm
- Zip Code: 74070
- Circle of Safety: Y
- Location: OK, Skiatook
Re: Angle Snowplow Blade Manually
Simply elegant Involves just enough fabrication to make it interesting (without $$$$$ in machine tools required) and it is an inexpensive major improvement. Question: How far out can you have an adjustable axle before it starts interfering with needed blade angle
-
- Team Cub
- Posts: 11884
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Angle Snowplow Blade Manually
Very nice job Dave. By the way, did you ever get that stump pushed over?
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 3562
- Joined: Thu Apr 22, 2010 2:31 pm
- Zip Code: 17953
- Tractors Owned: ......Almost enough.
N3NIK - Circle of Safety: Y
- Location: PA, Middleport (Schuylkill County)
Re: Angle Snowplow Blade Manually
Bill E Bob wrote: Question: How far out can you have an adjustable axle before it starts interfering with needed blade angle
Bill...my axle is out pretty far...doesn't hit it...others will probably chime in today.
Bob McCarty wrote:Very nice job Dave. By the way, did you ever get that stump pushed over? Bob
Bob...I actually did a test of swiveling the blade by dragging it on the ground, but didn't video it.
Dave
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
-
- 10+ Years
- Posts: 1300
- Joined: Tue Nov 23, 2004 7:21 pm
- Zip Code: 24095
- Tractors Owned: '49 Cub
'49 JD "B"
'79 JD 2040
'50 DB "Garden Tractor"
'52 DB "Super Power"
'56 DB "Big 5"
'62 DB "Super 600"
'37 McCormick Deering "LA" engine - Location: Stewartsville, Virginia
Re: Angle Snowplow Blade Manually
Well done!
Best,
Mike
Tractors are made to work!
"A Cub will do as much as a team of horses,.. More in hot weather!" - C. W. Spradlin 1909-1994
Mike
Tractors are made to work!
"A Cub will do as much as a team of horses,.. More in hot weather!" - C. W. Spradlin 1909-1994
-
- Team Cub Guide
- Posts: 5636
- Joined: Mon Nov 01, 2004 7:24 am
- Zip Code: 43528
- Tractors Owned: 47(circle cub),48(Floyd backhoe),49,,51,54 and another 55
- Circle of Safety: Y
- Location: OH, Holland
Re: Angle Snowplow Blade Manually
I replaced the bolt thru the steering post with an eyebolt. Can you guess what it was from?
I hope you didn't snatch that off the neighbor's swingset
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
-
- 10+ Years
- Posts: 3562
- Joined: Thu Apr 22, 2010 2:31 pm
- Zip Code: 17953
- Tractors Owned: ......Almost enough.
N3NIK - Circle of Safety: Y
- Location: PA, Middleport (Schuylkill County)
Re: Angle Snowplow Blade Manually
Rick Prentice wrote:I replaced the bolt thru the steering post with an eyebolt. Can you guess what it was from?
I hope you didn't snatch that off the neighbor's swingset
Rick...YOU have the correct answer and win the contest.... and maybe a calendar...Oh wait, no calendars here.
Dave
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
-
- 10+ Years
- Posts: 256
- Joined: Fri Sep 10, 2010 6:02 pm
- Zip Code: 44045
- Tractors Owned: 1948 cub (Sophie)
1949 cub Loren
1954 cub Nussie - Location: OH, Grand River (east of Cleveland)
Re: Angle Snowplow Blade Manually
Nice job Dave,
I think it should be called the "Winfield" cold weather seat time increaser. What do you think?
Really nice work, it is always nice to see the birth of an idea turn into a success!!!
Dave
I think it should be called the "Winfield" cold weather seat time increaser. What do you think?
Really nice work, it is always nice to see the birth of an idea turn into a success!!!
Dave
The glass is half full
the upper portion is wasted material
the content is delicious, cold and refreshing!
the upper portion is wasted material
the content is delicious, cold and refreshing!
-
- 10+ Years
- Posts: 323
- Joined: Thu Mar 22, 2007 6:50 am
- Zip Code: 02830
- Location: Burrillville, RI
Re: Angle Snowplow Blade Manually
Thanks for posting the pics and video Dave, that really came out neat.
I love to see the video, it really shows how well it works,
Dave
I love to see the video, it really shows how well it works,
Dave
-
- Similar Topics
- Replies
- Views
- Last post
-
- 10
- 520
-
by Greenthumbfarms
Sun Jan 23, 2022 3:24 pm
-
- 0
- 130
-
by ShawnAgne
Sun Aug 22, 2021 8:32 pm
-
-
International LoBoy L-54 Front Blade Hydraulic Angle Build Attachment(s)
by GoldenLoBoy » Wed Jul 14, 2021 8:43 pm » in Farmall Cub - 11
- 455
-
by ricky racer
Fri Jul 16, 2021 8:03 am
-
-
- 16
- 1019
-
by staninlowerAL
Mon Jan 17, 2022 9:32 am
-
- 5
- 264
-
by AHS
Sat Aug 21, 2021 6:36 pm
Who is online
Users browsing this forum: Majestic-12 [Bot] and 4 guests