This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Need help about Model 20 buzz saw
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 5
- Joined: Sun May 09, 2004 6:12 pm
Need help about Model 20 buzz saw
I picked up a Cub sawyer Model 20 buss saw. I was hoping someone out there can help with some parts or a manual and information. Any help will be appreciated.
-
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
I have a buzz saw that has been mounted on the side of an old chasis. A 60 cu in int runs it. I can't tell you much abpou it other than it used to work but have not used it in 4 or 5 years. PM me and any measurements or the like I can do Tues and will send them to you. I am up the country and have to go to the Library when it is open to access the forum. I have some pictures and will take more. I will have to have someone lead me by the hand to post them
Bill
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
-
- 10+ Years
- Posts: 1224
- Joined: Sun Feb 02, 2003 1:11 pm
- Zip Code: 28001
- Location: Albemarle, North Carolina 28001
BigDog has some pictures here http://www.picturetrail.com/gallery/view?p=999&gid=5317473&uid=1221583&members=1
Young man for work, old man for advice
-
- 10+ Years
- Posts: 1224
- Joined: Sun Feb 02, 2003 1:11 pm
- Zip Code: 28001
- Location: Albemarle, North Carolina 28001
Here is a picture
http://farmallcub.com/gallery/album28/aap?full=1
http://farmallcub.com/gallery/album28/aap?full=1
Young man for work, old man for advice
-
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
What i have would have been a stand alone buzz saw run by a belt from the belt pulley on a PTO. It has been shade tree mechaniced to the side of an old Chasis of some kind. I will take pictures and try to post when I get home.
Bill
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
-
- Team Cub Mentor
- Posts: 17488
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
-
- 10+ Years
- Posts: 5
- Joined: Sun May 09, 2004 6:12 pm
-
- 10+ Years
- Posts: 5
- Joined: Sun May 09, 2004 6:12 pm
-
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
Eddie all the mountig shown is a table on angle iron that pivots on mounts on the draw bar. The dimensions should be that you are cutting well above what would be a horizontal through the shaft that the blade is fastened to. You want to be above center at all locations of the table. You don't want anything to get jammed against the table. Strange that I don't see any saw dust in the picture.
The trouble that I have when using mine is that you can only handle relatively short pieces, 10 or 12 feet. I was always giong to build some sort of an aux table to hold the weight of the off end till I had them short enough that I could handle them on the pivoting cutting table. I also founf that if I fed the pieces so that I cut the thicker end first they are easier to handle. Of course with a helper holding the off end till you get the logs short enough helps but i just can't get my wife to go along with the plan.
Bill
The trouble that I have when using mine is that you can only handle relatively short pieces, 10 or 12 feet. I was always giong to build some sort of an aux table to hold the weight of the off end till I had them short enough that I could handle them on the pivoting cutting table. I also founf that if I fed the pieces so that I cut the thicker end first they are easier to handle. Of course with a helper holding the off end till you get the logs short enough helps but i just can't get my wife to go along with the plan.
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Cub Buzz Saw Manufacturers? Attachment(s)
by CapeCodCubs » Sat Oct 02, 2021 9:32 pm » in Farmall Cub - 3
- 291
-
by BSR
Mon Oct 04, 2021 3:12 am
-
-
-
Cub fast hitch vs. Lo-boy FH implements, also Mott sawyers buzz saw Attachment(s)
by rjfcsa » Fri Feb 16, 2024 6:36 pm » in Farmall Cub - 3
- 246
-
by rjfcsa
Mon Feb 19, 2024 11:50 am
-
-
- 7
- 301
-
by Glen
Wed Jun 07, 2023 10:10 pm
-
- 7
- 366
-
by Glen
Tue Mar 12, 2024 6:00 pm
-
- 4
- 260
-
by SamsFarm
Thu May 11, 2023 12:32 am
Who is online
Users browsing this forum: Majestic-12 [Bot], wrz and 9 guests