I dismantled the front axle on my 1957 Cub Lo-Boy to do a rebuild. However, when I started to put the pieces back together, I have 2 extra concave washers that I'm not sure where they go. They're about 3/4"OD with a 5/16" hole in the center. I thought they went into the tie rod ends behind the buttons that hold the steering knuckle ball , but they don't seem to fit. I can't find a good diagram of the tie rod ends or the steering shaft assembly where the tie rods ends come together. Do the tie rod ends only have the concave buttons and the threaded keeper in the assembly? Could these washers be spacers for the 2 piece assembly where the tie rods meet the steering arm?
I want to compliment the organizations sponsoring the Portland Indiana tractor show. It was very enjoyable, but too big for the one day I spent. It's nice to see a show with Vendors who sell tractor parts instead of Beanie Babies. I also met Larry from the ATIS and was very impressed with his Low-boys and his hospitality.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Steering rebuild question
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 137
- Joined: Fri Jul 02, 2004 7:12 pm
- Zip Code: 49032
- Location: Centreville, MI. 49032
-
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
Tom,
The "buttons" belong behind the ball in the tie rod ends. They are a fairly close fit, so they can't be allowed to cock. You'll notice that they have the same curvature as the threaded end... and together they can be adjusted to a good fit on the ball.
Too bad you didn't have more time and come to spend a little time with the rest of us at the camp site. Larry is a very good friend and will be coming to our home show next weekend for a continuation of the festivities at Gibsonburg, OH.
Larry picked up his new Cub in Wisconsin and delivered it to Portland just before the show.
Larry's Cub:
Larry's wife, Barb bought her Cub the week before CubFest 2003. It was among the 12 ATIS tractors displayed as a group.
Here it is at CubFest 2003 at my place:
The "buttons" belong behind the ball in the tie rod ends. They are a fairly close fit, so they can't be allowed to cock. You'll notice that they have the same curvature as the threaded end... and together they can be adjusted to a good fit on the ball.
Too bad you didn't have more time and come to spend a little time with the rest of us at the camp site. Larry is a very good friend and will be coming to our home show next weekend for a continuation of the festivities at Gibsonburg, OH.
Larry picked up his new Cub in Wisconsin and delivered it to Portland just before the show.
Larry's Cub:
Larry's wife, Barb bought her Cub the week before CubFest 2003. It was among the 12 ATIS tractors displayed as a group.
Here it is at CubFest 2003 at my place:
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- Similar Topics
- Replies
- Views
- Last post
-
- 11
- 281
-
by Greenthumbfarms
Sun Feb 13, 2022 6:32 pm
-
-
Question about ‘49 Farmall Cub Steering Attachment(s)
by AndiMac » Mon Sep 06, 2021 10:38 pm » in Farmall Cub - 18
- 631
-
by Eugene
Sun Sep 19, 2021 9:53 pm
-
-
-
47 Cub steering leak and hard steering Attachment(s)
by AHS » Sun Jun 05, 2022 6:27 am » in Farmall Cub - 10
- 521
-
by Glen
Tue Jun 14, 2022 7:14 pm
-
-
- 5
- 624
-
by inairam
Thu Aug 24, 2023 6:07 am
-
- 11
- 494
-
by Bob McCarty
Thu Mar 24, 2022 2:03 pm
Who is online
Users browsing this forum: Cub driver, Kalebtrojacek, Majestic-12 [Bot] and 3 guests