This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Wheel noise
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Wheel noise
For the last 6 months or more My old 48 cub has been making a very faint occasional squawking noise around the left rear wheel. I'd gone over all the wheel bolts, center and rim, as well as the wheel weight bolts, and even checked for play in the brake drum in case the set screw had come loose or broken. I had come to the conclusion it was a bearing starting to go bad, but with my health I had decided it was going to have to wait , and was keeping use to a minimum hoping to do as little damage as possible. I was using the disk yesterday to go over some ground I'd plowed 2 years ago but had been unable to disk up, and when I backed up to unhitch I saw a movement out of the corner of my eye. I started watching closely and could see a very tiny back and forth movement of the left fender as I went from forward to reverse in the soft ground. When I got it back to the shed and checked, every bolt holding the final drive was just finger tight. Apparently when I replaced the left brake drum about 4 or 5 years ago I failed to tighten the bolts. I tightened all the bolts, and it is in the plans to someday, when I feel like it and have some help available, to pull the final and replace the dowel pins which I assume had become worn due to the loose bolts, and was allowing the movement. The only thing I can claim as an excuse is that when I was replacing the drum I was working under a lean-to shed that was only a foot wider than the tractor and I was standing in snow doing the reassembly. That's my story and I'm sticking to it.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 1041
- Joined: Mon Jun 28, 2004 1:45 pm
- Zip Code: 00000
- Tractors Owned: 1950 Cub
2000 Simplicity Landlord DLX
1988 JD 322 Garden Tractor with hydraulic scoop, 54" scrape blade and 48" mower deck, Haban 3 pt hitch sickle bar mower
2014 LS XR3032H w/ FEL and BH - Circle of Safety: Y
Yeah, and ...
Where's the hammock?
Though trillions and trillions of eyes have been watching the skies for as long as human memory exists, no gods nor angels have been seen or documented outside of religion. The number of spaceships being sighted however has become much more prevalent.
- artc
- Cub Pro
- Posts: 1871
- Joined: Sun Mar 30, 2003 10:25 am
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: Restored: 1950 Cub, 1950 Cub Demo, 1948 super AI, 1935 Silver King, 1946 Oliver 60 RC, John Deere M, 1950 C demo.
In working clothes:
1950 cub, 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial. IH 450, 1963, another 1948 cub, 1946 I6 with Trogan front blade. - Location: CT, Middletown
- Contact:
well, glad you caught that one before 'you picked a fine to leave me loose wheel'
iff'n your not careful, though, you could pick up a reputation as ' johnny hand tight'.
iff'n your not careful, though, you could pick up a reputation as ' johnny hand tight'.
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
- George Willer
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
- Contact:
John,
It sounds like you caught it in time. I wouldn't worry about the hardened dowel pins wearing... any wear would be expected on the cast iron.
A couple of my project tractors showed up with problems from the bolts being loose. One had a broken flange on the axle tube... and a replacement from J.P.'s was an easy solution. The other had the tapped holes in the transmission case ruined. The ruined holes problem was compounded by an inept repair... made for a LOT of work!
This is an area we all should check to make sure they are tight.
It sounds like you caught it in time. I wouldn't worry about the hardened dowel pins wearing... any wear would be expected on the cast iron.
A couple of my project tractors showed up with problems from the bolts being loose. One had a broken flange on the axle tube... and a replacement from J.P.'s was an easy solution. The other had the tapped holes in the transmission case ruined. The ruined holes problem was compounded by an inept repair... made for a LOT of work!
This is an area we all should check to make sure they are tight.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
Who is online
Users browsing this forum: No registered users and 47 guests