c-3 mower spindle bearing number

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
User avatar
cjpenny89
10+ Years
10+ Years
Posts: 1073
Joined: Mon Feb 03, 2003 1:15 pm
Location: St. Charles, MI 48655

c-3 mower spindle bearing number

Postby cjpenny89 » Mon May 03, 2004 7:48 am

I am going to rebuild my bearing spindles on my c-3 mower and I was hoping to find the bearing numbers for the spindle so I can have them before I tear them down. does anyone have the part numbers?
Chad

Preacherman
10+ Years
10+ Years
Posts: 121
Joined: Thu Feb 13, 2003 1:05 am
Location: Mt. Washington, KY

Postby Preacherman » Tue May 04, 2004 10:09 am

Chad,

I have a copy of the manual but no part's list.

Probably a call to Case/IH dealer will make a long search and short one.

My local NAPA had most of the common TIMKEN #'s available.

Others will probably know more.
Sam "Preacherman" Fowler

God built us a bridge to heaven with two boards and three nails.

User avatar
Bigdog
Cub Pro
Cub Pro
Posts: 24066
Joined: Sun Feb 02, 2003 12:50 pm
Zip Code: 43113
Circle of Safety: Y
Location: OH, Circleville

Postby Bigdog » Tue May 04, 2004 10:16 am

Chad, Jim Hudson just mentioned doing this to a C-2 spindle. (ATIS list) He didn't mention any bearing numbers, but they should be readily available at NAPA or similar location.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.

My wife says I don't listen to her. - - - - - - - - Or something like that!

Image

http://www.cubtug.com

User avatar
Bermuda Ken
10+ Years
10+ Years
Posts: 641
Joined: Fri Feb 07, 2003 8:43 am
Zip Code: 53521
Tractors Owned: Tractors owned past/present:

Farmall.....F-1206, F-806 sn#501.

Cub Cadet...Original(s), 122, Spirit of 76, 1200, 1250, 1450, 782, 782 Diesel (2), 984, 982 CADET 000 LT Prototype.
Circle of Safety: Y
Location: Wisconsin.......The Badger State

Postby Bermuda Ken » Tue May 04, 2004 11:38 am

Here's a quick bearing conversion chart:

IH part # 463911R91..........brg cone..............L44643 Timken
IH part # 572564R1...........brg cup/race...........L44610 Timken

The bearings from IH are reasonably priced and are Genuine Timken brand too.
Cub Cadets....Engineered for people who know better!

User avatar
Peter S
10+ Years
10+ Years
Posts: 47
Joined: Fri Jul 18, 2003 11:24 am
Zip Code: 01085
Tractors Owned: 1951 cub
1963 cub
Location: Massachusetts, Westfield

Postby Peter S » Tue May 04, 2004 3:47 pm

I got the complete US made bearing assembly from Carquest under the part number of "A-14" for about $8.00 each. The seal part number is National 471750.
Peter

1951 Cub, 1963 Cub

User avatar
cjpenny89
10+ Years
10+ Years
Posts: 1073
Joined: Mon Feb 03, 2003 1:15 pm
Location: St. Charles, MI 48655

Postby cjpenny89 » Wed May 05, 2004 6:46 am

thank you very much guys! that is the same part numbers that my sun master clipper "KUB KLIPPER" 60" mower uses. best thing about that is I can walk into autozone and buy a timken wheel bearing kit for $10 and it has both bearing and cones and the seals are stock items here at work and all I have to do is pay the parts room for them.
thank you again!
Chad Penny

User avatar
Peter S
10+ Years
10+ Years
Posts: 47
Joined: Fri Jul 18, 2003 11:24 am
Zip Code: 01085
Tractors Owned: 1951 cub
1963 cub
Location: Massachusetts, Westfield

Postby Peter S » Wed May 05, 2004 7:52 am

Chad, do you have a part number for the Timken bearing set that you get from Autozone?
Peter



1951 Cub, 1963 Cub

User avatar
cjpenny89
10+ Years
10+ Years
Posts: 1073
Joined: Mon Feb 03, 2003 1:15 pm
Location: St. Charles, MI 48655

Postby cjpenny89 » Wed May 05, 2004 9:24 am

well its been a while since I bought one 2 summers ago. I went in asked for the same numbers as was said above and the guy looked it up and he walked out to the shevles and he grabbed a bearing kit. It had timken bearings in it. I guess just look by the trailer stuff. I will look today at lunch if I get a chance.
Chad


Return to “Farmall Cub”

Who is online

Users browsing this forum: midmo, Steve Butram and 2 guests