Cub Parts

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

Cub Parts

Postby Ron » Tue Jan 27, 2004 9:19 pm

Hi All,

I've deceided that my Touch control system needs to be rebuilt.
I've looked in the manuals I have and don't see any instructions on how to go about this.
Is this something that can be done by looking at the schematic?
Also, is there a substitute for the I/H hydraulic fluid that I will need?
Where can I order a rebuild kit for this?
Where can I get a replacement voltage regulator?

Thanks in advance!!

Ron
1951 Farmall Cub
Ron
Cub Star
Cub Star
 
Posts: 80
Joined: Sat Feb 08, 2003 11:23 am
Location: Columbus, Georgia

Postby Rudi » Tue Jan 27, 2004 9:39 pm

Ron:

I've looked in the manuals I have and don't see any instructions on how to go about this.


Check out the server - got to Cub Maintenance Manuals and then to the Touch Control Manual. Btw - that is an excerpt from the GSS-1411 Service Manual which is also on the server under the Blue Ribbon Service Manuals.

Also, is there a substitute for the I/H hydraulic fluid that I will need?


Use the IH Touch Control Fluid if you are reasonably near to a CaseIH Dealer. It is the best. And (thanks David, I forgot), it is called Hy-Tran. However, some of the other guys use substitutes, just make sure it meets or exceeds the requirements listed on a Touch Control jug. Maybe one of the guys will post the specs.

Where can I order a rebuild kit for this?


Your CaseIH Dealer. You can also order them on line. Other suppliers will have it as well and I think CNGO has is. Be sure to check the part number on your pump as there apparently are two different versions and the seals are not interchangeable.

John Puckett can explain that one better.

As for the voltage regulator or is it a cut-out?. can be purchased from CaseIH as well. There should be subs available at NAPA, CarQuest etc.

Hope this helps
Last edited by Rudi on Tue Jan 27, 2004 10:56 pm, edited 1 time in total.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship

User avatar
Rudi
Team Cub
Team Cub
 
Posts: 28425
Joined: Sun Feb 02, 2003 8:37 pm
Location: NB Dieppe, Canada
Zip Code: E1A7J3
eBay ID: ve9rhs
Skype Name: R.H. "Rudi" Saueracker, SSM
Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1951 Cub "Jethro"
Dad's Putt-Putt
IH 129 CC
Circle of Safety Award
Circle of Safety: Y
Twitter ID: Rudi Saueracker, SSM

Postby parts man » Tue Jan 27, 2004 10:37 pm

The touch control fluid is now called HY-TRAN fluid. It's the best choice.
V.P. of T.S.A. (taking stuff apart)
User avatar
parts man
501 Club
501 Club
 
Posts: 619
Joined: Wed Jul 30, 2003 9:41 pm
Location: Sussex N.B. Can.

Postby rleggitt » Wed Jan 28, 2004 7:49 pm

Hi Ron.

I found that the instructions in the service manual [GSS-1411] section 8
was quiet adequate. I recently overhauled the one on my 1963. I would
suggest that you go to the parts house and get you a good set of pliers as
shown on page 8-19. I did not and ended up scratching the cylinder and
dad to hone it out.

Please pay "SPECIAL ATTENTION" to the NOTE on page 8-20 concerning
the Reassembly of parts with o-rings or seals. Be sure to lubricate all
parts before reassembly.

If you can get your hands on the TC-37F parts catalog in section 10
Hydraulics [10 pages] you will find all you need.

Hope this has helped.
rleggitt
Cub Star!!
Cub Star!!
 
Posts: 251
Joined: Sun Feb 09, 2003 10:05 pm
Location: MS, Oxford

Postby Rudi » Wed Jan 28, 2004 8:52 pm

Ron:

I forgot about this one. In the Blue Ribbon Service Manuals section you will see the GSS-1024 Touch Control... it seems to be the general service manual for all Farmall Touch Controls.

It may offer some additonal insight.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship

User avatar
Rudi
Team Cub
Team Cub
 
Posts: 28425
Joined: Sun Feb 02, 2003 8:37 pm
Location: NB Dieppe, Canada
Zip Code: E1A7J3
eBay ID: ve9rhs
Skype Name: R.H. "Rudi" Saueracker, SSM
Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1951 Cub "Jethro"
Dad's Putt-Putt
IH 129 CC
Circle of Safety Award
Circle of Safety: Y
Twitter ID: Rudi Saueracker, SSM

Postby Ron » Sat Jan 31, 2004 8:34 pm

Hi Guy's,

Thanks for all the help!!(again)

I found the parts for the touch control overhaul and will began as soon as they arrive.

On a side note(low engine compression) posted earlier.
I tried putting some Marvel Mystery Oil in each clyinder and let it sit for a couple of days. I started her up and let her run for an hour.
After wiping up all the oil spattered all over the shop I did another compression check.
I picked up 12 to 15 #'s . It's up to approx 75 # in each cylinder.
I was surprised at how much this seem to help in power when climbing a hill.
I figure she still needs to be rebuilt but now will wait for a little warmer weather.

Thanks,

Ron
1951 Farmall Cub
Ron
Cub Star
Cub Star
 
Posts: 80
Joined: Sat Feb 08, 2003 11:23 am
Location: Columbus, Georgia

Postby JackF » Sat Jan 31, 2004 9:59 pm

This is what I found

U S A Citgo Petroleum Corporation Hy-Tran Fluid IH® and Case
SAE Grade 10W-20
Gravity, ASTM D 287, °API 27.8
Pounds/Gallon 7.4
Specific Gravity 0.89
Viscosities:
@ -18°C., cP. 1850
@ 40°C., cSt. 41.9
@ 100°C., cSt. 6.6
@ 100°F., cSt. (SUS) 46.6 (217)
@ 210°F., cSt. (SUS) 6.78 (48.4)
Viscosity Index 111
Flash Point, ASTM D 92, COC, °F. (°C.) 400 (204)
Fire Point, ASTM D 92, COC, °F. (°C.) 440 (227)
Pour Point, ASTM D 97, °F. (°C.) -45 (-43)
Color, ASTM D 1500 7.5
Color, Observed Red-Brown
TYPICAL PROPERTIES:
For use in Case IH® Equipment
Hy-Tran®, CaseIH®, IH® and Case® are registered trademarks of the Case Corporation
I’m really good at doing nothing…With that said…I’m really, really good at doing nothing
JackF
501 Club
501 Club
 
Posts: 904
Joined: Sat Feb 15, 2003 7:20 am
Zip Code: 00000

I have and use the # GSS-1024

Postby countershaft » Sat Jan 31, 2004 10:11 pm

touch - control serviceman's handbook. What's the difference ? Maybe I'm missing something ? This services the Farmall Cub, SA & AV, C & Super C and the International SA
countershaft
Cub Star!!
Cub Star!!
 
Posts: 371
Joined: Mon Jun 30, 2003 9:14 pm
Location: Ridgway,Pa


Return to Farmall Cub

Who is online

Users browsing this forum: Arthur Luke, jpcubs, twotone and 7 guests