This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
C3 Mower
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 251
- Joined: Thu Mar 16, 2006 6:27 pm
- Zip Code: 01516
- Location: Douglas, Mass
C3 Mower
I need to replace the bearings on the blade spindles. I removed the 3 bolts on the belt pulley but I cannot figure out how to remove the pulley. Is the pulley a press fit and do I need a puller to remove the belt pulley from the spindle? Thanks for any help Dave. It is a C3 mower
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Dave,
there should be either two or three threaded holes, run the bolts you took out into the treaded holes and tighten them evenly, the pulley should come loose.... be sure to tighten evenly , or you coud break a bolt off.
there should be either two or three threaded holes, run the bolts you took out into the treaded holes and tighten them evenly, the pulley should come loose.... be sure to tighten evenly , or you coud break a bolt off.
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- 10+ Years
- Posts: 418
- Joined: Sat Jan 17, 2004 6:40 pm
- Location: Lordstown, Ohio
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
Dave,
i agree with John, but you could try loosing the bolts and get a chisel and put it between the taper lock and pully and hit the chisel, moving around the pulley on each hit. sometimes that will know the taperlock loose.
i agree with John, but you could try loosing the bolts and get a chisel and put it between the taper lock and pully and hit the chisel, moving around the pulley on each hit. sometimes that will know the taperlock loose.
'49 Cub (Vince)
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
'41 allis B with Woods L59 mower
656 Wheel Horse with 42” sickle mower
C-165 Wheel Horse
Simplicity 20 HP Sunstar
Honda 48” walk behind mower
-
- 10+ Years
- Posts: 251
- Joined: Thu Mar 16, 2006 6:27 pm
- Zip Code: 01516
- Location: Douglas, Mass
c3 mower
I was able to remove the 3 bolts from the left side pulley I then used a pitman arm puller to remove the taper lock. Thanks for your help. I think the reason the left side pulley is mounted that way is because the belt that goes from the left side to the center pulley goes on first and needs to be lower than the right side. If anyoney that has one of these mowers could take a look to see how their pulleys are mounted I would be greatful. Thanks again for all the help. Dave
-
- 10+ Years
- Posts: 1776
- Joined: Thu Oct 26, 2006 7:17 pm
- Zip Code: 44657
- Circle of Safety: Y
- Location: Minerva,Ohio
-
- 10+ Years
- Posts: 341
- Joined: Wed Nov 08, 2006 9:35 pm
- Location: Backswamp North Carolina
- Contact:
I Have A C3
I ran out to the tractor shed and looked(IN my PJs Buuuuuuuuuuurr) One of my pulleys is sitting higher then the other and It has nuts on top the opposite one has bolt heads. Mine has the original Danco Spindles. Hope that helps
1961 Cub
1948 Cub
1960 CUB
1964 CUB CADET 100
23A Disc,2-C-22 sickles,54 Blade,152 disc,38a lift disc,C2 Mower,Kub Klipper, and a side dresser.
1948 Cub
1960 CUB
1964 CUB CADET 100
23A Disc,2-C-22 sickles,54 Blade,152 disc,38a lift disc,C2 Mower,Kub Klipper, and a side dresser.
Who is online
Users browsing this forum: No registered users and 36 guests