This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Measurements needed from IH-1000 loader
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 395
- Joined: Sun Feb 02, 2003 10:34 pm
- Location: Long Island, NY
Measurements needed from IH-1000 loader
Can someone help with measurement's on a 1000 loader bucket? I will not be ableyo get them myself for a few weeks. I am looking forthe brackets on the back of the bucket where the bucket pivot pin and pin for the dump cyclrder. I think the 1 end is 6" and tapers to 4" and about 18" long if I remember right. Not sure how thick the steel is and what size the pin holes might be. any help would be great and a drawing would be even better. Thank you
-
- 10+ Years
- Posts: 395
- Joined: Sun Feb 02, 2003 10:34 pm
- Location: Long Island, NY
Re: Measurements needed from IH-1000 loader
Anyone have a IH-1000 loader to help? It is now going to be longer before I can get to mind. I just tested postive for COVID so stuck home for at least the next 10 days. Would like something to do if I am up to it. Thanks again for any help.
-
- 10+ Years
- Posts: 1179
- Joined: Sat Jan 28, 2012 3:13 pm
- Zip Code: 68803
- Tractors Owned: 1948 Cub, Kittie; 1948 Cub, Harold; 1949 Cub, 49er; 1951 Cub, Tucker; 1951 Cub, Homely; 1956 Cub High Crop; 1957 Cub Loboy; 57 Cub Loboy w/fasthitch + 194 plow; 1958 Cub LoBoy w/FH, Popeye; 1961 Cub, Beater; #1-1962 Cub Loboy Dually (Originally Orange) w/Foot Throttle; #2-1962 Cub Loboy Dually (Originally Orange) w/Foot throttle; Yellow 1963 Cub Loboy and blade; 1970 Cub, Cubbie; and 5 other Cubs in various stages of disaasembly and disrepair; 1962 Cub Cadet Original; 2 other Cub Cadet Originals; Cub Cadet 100; Cub Cadet 124 w/Creeper; Cub Cadet 147; 2 Cub Cadet 129's; Cub Cadet 149; 1948 Allis Chalmers C w/single frontwheel; 1944 Farmall H w/Tokhiem Cab; 2 One Point Fasthitch Carriers; 2-#100 Fasthitch Rear Blade; 2 Sets Cub 144 Cultivators; 2 Sets Cub #252 Cultivators; 3 Cub #193 Mouldboard Plows; 1 Cub #193 Slatted Plow; 1 1948 Cub-54 Snow Plow; 3 Cub-54 49-5 Snow Plows; Cub #6 Tool Bar w/Disc Blades & Middlebuster. 2-#105 sickle mowers, #152 disc plow
- Circle of Safety: Y
- Location: Grand Island, Nebraska
Re: Measurements needed from IH-1000 loader
I have one but it’s too far away to get measurements. Sorry …BTW, Take care of yourself and get better soon. That COVID-19 is nothing to mess with.
Frank
-
- 10+ Years
- Posts: 395
- Joined: Sun Feb 02, 2003 10:34 pm
- Location: Long Island, NY
Re: Measurements needed from IH-1000 loader
Thanks for the well wishes, I am doing ok so far. I know there are plenty of guys here with the loader. Hope someone can help.
-
- 10+ Years
- Posts: 395
- Joined: Sun Feb 02, 2003 10:34 pm
- Location: Long Island, NY
Re: Measurements needed from IH-1000 loader
Can anyone tell me how thick the steel is 3/8" or 1/2" ? I would like to order the steel I need ahead of time. I have never had so much trouble getting info from members on this site.
"
"
-
- 10+ Years
- Posts: 3328
- Joined: Fri Jan 11, 2008 5:30 pm
- Zip Code: 02747
- Tractors Owned: .
1948 F Cub Fast hitch
1949 F Cub
1950 F Cub Fast hitch
1965 Loboy Fast hitch
1966 Loboy with 1000 loader
1976 International Cub
several walk behind garden tractors
(20) FastHitch implements
tons' of cultivating and planting stuff
C-16 Cub Middlebuster
(2) A33 Cub bean harvester
NOS Planet Jr. planter
172 planter, large combo hopper, 101A fertilzer hopper
Cole 250# fertilizer hopper with chain drive. - Location: MA, Dartmouth
Re: Measurements needed from IH-1000 loader
Hi Bob,
I meant to get this a lot earlier for you.
The angled piece welded to the back of the bucket is 18 1/2 long.
The taper is 2 1/2 wide at the upper vertical and 5" at the bottom vertical.
The thickness is 3/8"
call me at 77four 22five 861zero and I will send you a detailed mark of the piece.
I can also sketch the profile and the distance to the center of the holes
The top vertical has a taper. I can detail the entire piece for you..
Chris
I meant to get this a lot earlier for you.
The angled piece welded to the back of the bucket is 18 1/2 long.
The taper is 2 1/2 wide at the upper vertical and 5" at the bottom vertical.
The thickness is 3/8"
call me at 77four 22five 861zero and I will send you a detailed mark of the piece.
I can also sketch the profile and the distance to the center of the holes
The top vertical has a taper. I can detail the entire piece for you..
Chris
-
- 10+ Years
- Posts: 395
- Joined: Sun Feb 02, 2003 10:34 pm
- Location: Long Island, NY
Re: Measurements needed from IH-1000 loader
Thank you so much Chris. I will call you this weekend, Bob
-
- 10+ Years
- Posts: 3328
- Joined: Fri Jan 11, 2008 5:30 pm
- Zip Code: 02747
- Tractors Owned: .
1948 F Cub Fast hitch
1949 F Cub
1950 F Cub Fast hitch
1965 Loboy Fast hitch
1966 Loboy with 1000 loader
1976 International Cub
several walk behind garden tractors
(20) FastHitch implements
tons' of cultivating and planting stuff
C-16 Cub Middlebuster
(2) A33 Cub bean harvester
NOS Planet Jr. planter
172 planter, large combo hopper, 101A fertilzer hopper
Cole 250# fertilizer hopper with chain drive. - Location: MA, Dartmouth
-
- 10+ Years
- Posts: 395
- Joined: Sun Feb 02, 2003 10:34 pm
- Location: Long Island, NY
Re: Measurements needed from IH-1000 loader
Thanks so much for all the help Chris. I will get the photos yu want this week.
Thank you again.
Bob
Thank you again.
Bob
-
- Similar Topics
- Replies
- Views
- Last post
-
- 1
- 106
-
by Wingit
Thu Mar 16, 2023 1:50 pm
-
- 5
- 182
-
by inairam
Fri Sep 02, 2022 5:10 am
-
- 0
- 88
-
by baldwindiesel
Thu Jun 22, 2023 9:27 am
-
- 2
- 83
-
by baldwindiesel
Sat Apr 01, 2023 9:13 pm
-
-
What is the minimum needed for cub to run?
by Brandon966 » Fri Apr 01, 2022 6:40 am » in Farmall Cub - 7
- 406
-
by SamsFarm
Sat Apr 02, 2022 1:39 pm
-
Who is online
Users browsing this forum: No registered users and 3 guests