This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
C2 mower
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 5+ Years
- Posts: 15
- Joined: Sat Mar 03, 2018 11:48 pm
- Zip Code: 78942
C2 mower
Havent had any luck finding overrunning clutch pin & spring for c2 mower.so I'm going to use dowel pin & spring the same size as dowel pin . I'm going to drill holes all way thru on pulley then make a 1 inch thick washer and counter bore 4 holes for the spring and dowel washer to pulley so washer doesn't turn .I think it will work I have got over 40 year as a machinists. Thanks
-
- Team Cub
- Posts: 11827
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: C2 mower
Messick's shows both, but a set of 4 would cost about $175. Why can't you just replace the pins and springs?
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 5+ Years
- Posts: 15
- Joined: Sat Mar 03, 2018 11:48 pm
- Zip Code: 78942
Re: C2 mower
Internet show several places that had pins & springs but went I call they didnt have them. Inventory wrong
-
- Team Cub
- Posts: 11827
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: C2 mower
I guess I should have said why not make the pins, match the springs and reassemble. Here's where I got springs a few years ago:
https://www.springsfast.com/part_detail ... ?part=4147
https://www.springsfast.com/part_detail ... ?part=4147
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 5+ Years
- Posts: 15
- Joined: Sat Mar 03, 2018 11:48 pm
- Zip Code: 78942
Re: C2 mower
I have 2 pins but no spring,was thinking about pull out dowels and drilling the thread out to dimension of old pins.then get 4 spring from hardware store.
-
- Team Cub
- Posts: 11827
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: C2 mower
My link above gives the spring dimensions, etc. Pretty cheap from them.
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 5+ Years
- Posts: 2810
- Joined: Wed Jul 08, 2015 10:24 am
- Zip Code: 19342
- Tractors Owned: 1948 6v - Dozer
1949 with kub klipper belly mower. mag 6v - Mom
1950 with plow, 54 blade, mott mag 6v - Roxanne
1953 54 blade, c22, wood 42 6v
1957 6v - barn Queen
1965 lo-boy with c-3 mower 12 v - Loboy
1974 Horse II 12 v c-2
1975 with woods 42-6 12 v - Horse
1979 long strip 12 v stuck engine
130 with international 1000 loader 6 v
1969 140 with bush hog tow behind mower 12 v
Terramite T-6 4WD Backhoe Perkins diesel
Memberships: Rough and Tumble Engineers Historical Association;Chapter 8 IH Collectors; IH Collectors Worldwide - Circle of Safety: Y
- Location: Glen Mills PA
Re: C2 mower
Gidtex,
I have to work on my clutch and was able to purchase pins and springs from Messicks.
Why do you want to machine the pulley? What will the machining do?
I do not have any experience going into with this clutch but I do with the woods 42.
I have to work on my clutch and was able to purchase pins and springs from Messicks.
Why do you want to machine the pulley? What will the machining do?
I do not have any experience going into with this clutch but I do with the woods 42.
When you only have 9 horsepower you need to know the names of all of the ponies!
Who is online
Users browsing this forum: tgrist and 20 guests